summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--virtio-spec.txt2595
1 files changed, 2595 insertions, 0 deletions
diff --git a/virtio-spec.txt b/virtio-spec.txt
new file mode 100644
index 0000000..dcf3918
--- /dev/null
+++ b/virtio-spec.txt
@@ -0,0 +1,2595 @@
+This document describes the specifications of the “virtio” family
+of PCI devices. These are devices
+are found in virtual environments,
+yet by design they are not all that different from physical PCI
+devices, and this document treats them as such. This allows the
+guest to use standard PCI drivers and discovery mechanisms.
+
+The purpose of virtio and this specification is that virtual
+environments and guests should have a straightforward, efficient,
+standard and extensible mechanism for virtual devices, rather
+than boutique per-environment or per-OS mechanisms.
+
+ Straightforward: Virtio PCI devices use normal PCI mechanisms
+ of interrupts and DMA which should be familiar to any device
+ driver author. There is no exotic page-flipping or COW
+ mechanism: it's just a PCI device.[1]
+
+ Efficient: Virtio PCI devices consist of rings of descriptors
+ for input and output, which are neatly separated to avoid cache
+ effects from both guest and device writing to the same cache
+ lines.
+
+ Standard: Virtio PCI makes no assumptions about the environment
+ in which it operates, beyond supporting PCI. In fact the virtio
+ devices specified in the appendices do not require PCI at all:
+ they have been implemented on non-PCI buses.[2]
+
+ Extensible: Virtio PCI devices contain feature bits which are
+ acknowledged by the guest operating system during device setup.
+ This allows forwards and backwards compatibility: the device
+ offers all the features it knows about, and the driver
+ acknowledges those it understands and wishes to use.
+
+1.1 Virtqueues
+
+The mechanism for bulk data transport on virtio PCI devices is
+pretentiously called a virtqueue. Each device can have zero or
+more virtqueues: for example, the network device has one for
+transmit and one for receive.
+
+Each virtqueue occupies two or more physically-contiguous pages
+(defined, for the purposes of this specification, as 4096 bytes),
+and consists of three parts:
+
+
++-------------------+-----------------------------------+-----------+
+| Descriptor Table | Available Ring (padding) | Used Ring |
++-------------------+-----------------------------------+-----------+
+
+
+When the driver wants to send a buffer to the device, it fills in
+a slot in the descriptor table (or chains several together), and
+writes the descriptor index into the available ring. It then
+notifies the device. When the device has finished a buffer, it
+writes the descriptor into the used ring, and sends an interrupt.
+
+Specification
+
+2.1 PCI Discovery
+
+Any PCI device with Vendor ID 0x1AF4, and Device ID 0x1000 through
+0x103F inclusive is a virtio device[3]. The device must also have a
+Revision ID of 0 to match this specification.
+
+The Subsystem Device ID indicates which virtio device is
+supported by the device. The Subsystem Vendor ID should reflect
+the PCI Vendor ID of the environment (it's currently only used
+for informational purposes by the guest).
+
+
++----------------------+--------------------+---------------+
+| Subsystem Device ID | Virtio Device | Specification |
++----------------------+--------------------+---------------+
++----------------------+--------------------+---------------+
+| 1 | network card | Appendix C |
++----------------------+--------------------+---------------+
+| 2 | block device | Appendix D |
++----------------------+--------------------+---------------+
+| 3 | console | Appendix E |
++----------------------+--------------------+---------------+
+| 4 | entropy source | Appendix F |
++----------------------+--------------------+---------------+
+| 5 | memory ballooning | Appendix G |
++----------------------+--------------------+---------------+
+| 6 | ioMemory | - |
++----------------------+--------------------+---------------+
+| 7 | rpmsg | - |
++----------------------+--------------------+---------------+
+| 8 | SCSI host | Appendix I |
++----------------------+--------------------+---------------+
+| 9 | 9P transport | - |
++----------------------+--------------------+---------------+
+| 10 | mac80211 wlan | - |
++----------------------+--------------------+---------------+
+
+
+2.2 Device Configuration
+
+To configure the device, we use the first I/O region of the PCI
+device. This contains a virtio header followed by a
+device-specific region.
+
+There may be different widths of accesses to the I/O region; the
+“natural” access method for each field in the virtio header must be
+used (i.e. 32-bit accesses for 32-bit fields, etc), but the
+device-specific region can be accessed using any width accesses, and
+should obtain the same results.
+
+Note that this is possible because while the virtio header is PCI
+(i.e. little) endian, the device-specific region is encoded in
+the native endian of the guest (where such distinction is
+applicable).
+
+2.2.1 Device Initialization Sequence
+
+We start with an overview of device initialization, then expand
+on the details of the device and how each step is preformed.
+
+1. Reset the device. This is not required on initial start up.
+
+2. The ACKNOWLEDGE status bit is set: we have noticed the device.
+
+3. The DRIVER status bit is set: we know how to drive the device.
+
+4. Device-specific setup, including reading the Device Feature
+ Bits, discovery of virtqueues for the device, optional MSI-X
+ setup, and reading and possibly writing the virtio
+ configuration space.
+
+5. The subset of Device Feature Bits understood by the driver is
+ written to the device.
+
+6. The DRIVER_OK status bit is set.
+
+7. The device can now be used (ie. buffers added to the
+ virtqueues)[4]
+
+If any of these steps go irrecoverably wrong, the guest should
+set the FAILED status bit to indicate that it has given up on the
+device (it can reset the device later to restart if desired).
+
+We now cover the fields required for general setup in detail.
+
+2.2.2 Virtio Header
+
+The virtio header looks as follows:
+
+
++------------++---------------------+---------------------+----------+--------+---------+---------+---------+--------+
+| Bits || 32 | 32 | 32 | 16 | 16 | 16 | 8 | 8 |
++------------++---------------------+---------------------+----------+--------+---------+---------+---------+--------+
+| Read/Write || R | R+W | R+W | R | R+W | R+W | R+W | R |
++------------++---------------------+---------------------+----------+--------+---------+---------+---------+--------+
+| Purpose || Device | Guest | Queue | Queue | Queue | Queue | Device | ISR |
+| || Features bits 0:31 | Features bits 0:31 | Address | Size | Select | Notify | Status | Status |
++------------++---------------------+---------------------+----------+--------+---------+---------+---------+--------+
+
+
+If MSI-X is enabled for the device, two additional fields
+immediately follow this header:[5]
+
+
++------------++----------------+--------+
+| Bits || 16 | 16 |
+ +----------------+--------+
++------------++----------------+--------+
+| Read/Write || R+W | R+W |
++------------++----------------+--------+
+| Purpose || Configuration | Queue |
+| (MSI-X) || Vector | Vector |
++------------++----------------+--------+
+
+
+Immediately following these general headers, there may be
+device-specific headers:
+
+
++------------++--------------------+
+| Bits || Device Specific |
+ +--------------------+
++------------++--------------------+
+| Read/Write || Device Specific |
++------------++--------------------+
+| Purpose || Device Specific... |
+| || |
++------------++--------------------+
+
+
+2.2.2.1 Device Status
+
+The Device Status field is updated by the guest to indicate its
+progress. This provides a simple low-level diagnostic: it's most
+useful to imagine them hooked up to traffic lights on the console
+indicating the status of each device.
+
+The device can be reset by writing a 0 to this field, otherwise
+at least one bit should be set:
+
+ ACKNOWLEDGE (1) Indicates that the guest OS has found the
+ device and recognized it as a valid virtio device.
+
+ DRIVER (2) Indicates that the guest OS knows how to drive the
+ device. Under Linux, drivers can be loadable modules so there
+ may be a significant (or infinite) delay before setting this
+ bit.
+
+ DRIVER_OK (4) Indicates that the driver is set up and ready to
+ drive the device.
+
+ FAILED (128) Indicates that something went wrong in the guest,
+ and it has given up on the device. This could be an internal
+ error, or the driver didn't like the device for some reason, or
+ even a fatal error during device operation. The device must be
+ reset before attempting to re-initialize.
+
+2.2.2.2 Feature Bits
+
+The first configuration field indicates the features that the
+device supports. The bits are allocated as follows:
+
+ 0 to 23 Feature bits for the specific device type
+
+ 24 to 32 Feature bits reserved for extensions to the queue and
+ feature negotiation mechanisms
+
+For example, feature bit 0 for a network device (i.e. Subsystem
+Device ID 1) indicates that the device supports checksumming of
+packets.
+
+The feature bits are negotiated: the device lists all the
+features it understands in the Device Features field, and the
+guest writes the subset that it understands into the Guest
+Features field. The only way to renegotiate is to reset the
+device.
+
+In particular, new fields in the device configuration header are
+indicated by offering a feature bit, so the guest can check
+before accessing that part of the configuration space.
+
+This allows for forwards and backwards compatibility: if the
+device is enhanced with a new feature bit, older guests will not
+write that feature bit back to the Guest Features field and it
+can go into backwards compatibility mode. Similarly, if a guest
+is enhanced with a feature that the device doesn't support, it
+will not see that feature bit in the Device Features field and
+can go into backwards compatibility mode (or, for poor
+implementations, set the FAILED Device Status bit).
+
+2.2.2.3 Configuration/Queue Vectors
+
+When MSI-X capability is present and enabled in the device
+(through standard PCI configuration space) 4 bytes at byte offset
+20 are used to map configuration change and queue interrupts to
+MSI-X vectors. In this case, the ISR Status field is unused, and
+device specific configuration starts at byte offset 24 in virtio
+header structure. When MSI-X capability is not enabled, device
+specific configuration starts at byte offset 20 in virtio header.
+
+Writing a valid MSI-X Table entry number, 0 to 0x7FF, to one of
+Configuration/Queue Vector registers, maps interrupts triggered
+by the configuration change/selected queue events respectively to
+the corresponding MSI-X vector. To disable interrupts for a
+specific event type, unmap it by writing a special NO_VECTOR
+value:
+
+/* Vector value used to disable MSI for queue */
+
+#define VIRTIO_MSI_NO_VECTOR 0xffff
+
+Reading these registers returns vector mapped to a given event,
+or NO_VECTOR if unmapped. All queue and configuration change
+events are unmapped by default.
+
+Note that mapping an event to vector might require allocating
+internal device resources, and might fail. Devices report such
+failures by returning the NO_VECTOR value when the relevant
+Vector field is read. After mapping an event to vector, the
+driver must verify success by reading the Vector field value: on
+success, the previously written value is returned, and on
+failure, NO_VECTOR is returned. If a mapping failure is detected,
+the driver can retry mapping with fewervectors, or disable MSI-X.
+
+2.3 Virtqueue Configuration
+
+As a device can have zero or more virtqueues for bulk data
+transport (for example, the network driver has two), the driver
+needs to configure them as part of the device-specific
+configuration.
+
+This is done as follows, for each virtqueue a device has:
+
+1. Write the virtqueue index (first queue is 0) to the Queue
+ Select field.
+
+2. Read the virtqueue size from the Queue Size field, which is
+ always a power of 2. This controls how big the virtqueue is
+ (see below). If this field is 0, the virtqueue does not exist.
+
+3. Allocate and zero virtqueue in contiguous physical memory, on
+ a 4096 byte alignment. Write the physical address, divided by
+ 4096 to the Queue Address field.[6]
+
+4. Optionally, if MSI-X capability is present and enabled on the
+ device, select a vector to use to request interrupts triggered
+ by virtqueue events. Write the MSI-X Table entry number
+ corresponding to this vector in Queue Vector field. Read the
+ Queue Vector field: on success, previously written value is
+ returned; on failure, NO_VECTOR value is returned.
+
+The Queue Size field controls the total number of bytes required
+for the virtqueue according to the following formula:
+
+ #define ALIGN(x) (((x) + 4095) & ~4095)
+
+ static inline unsigned vring_size(unsigned int qsz)
+ {
+ return ALIGN(sizeof(struct vring_desc)*qsz + sizeof(u16)*(2 + qsz))
+ + ALIGN(sizeof(struct vring_used_elem)*qsz);
+ }
+
+This currently wastes some space with padding, but also allows
+future extensions. The virtqueue layout structure looks like this
+(qsz is the Queue Size field, which is a variable, so this code
+won't compile):
+
+ struct vring {
+ /* The actual descriptors (16 bytes each) */
+ struct vring_desc desc[qsz];
+
+ /* A ring of available descriptor heads with free-running index. */
+ struct vring_avail avail;
+
+ // Padding to the next 4096 boundary.
+ char pad[];
+
+ // A ring of used descriptor heads with free-running index.
+ struct vring_used used;
+ };
+
+2.3.1 A Note on Virtqueue Endianness
+
+Note that the endian of these fields and everything else in the
+virtqueue is the native endian of the guest, not little-endian as
+PCI normally is. This makes for simpler guest code, and it is
+assumed that the host already has to be deeply aware of the guest
+endian so such an “endian-aware” device is not a significant
+issue.
+
+2.3.2 Descriptor Table
+
+The descriptor table refers to the buffers the guest is using for
+the device. The addresses are physical addresses, and the buffers
+can be chained via the next field. Each descriptor describes a
+buffer which is read-only or write-only, but a chain of
+descriptors can contain both read-only and write-only buffers.
+
+No descriptor chain may be more than 2^32 bytes long in total.
+
+ struct vring_desc {
+ /* Address (guest-physical). */
+ u64 addr;
+ /* Length. */
+ u32 len;
+
+ /* This marks a buffer as continuing via the next field. */
+ #define VRING_DESC_F_NEXT 1
+ /* This marks a buffer as write-only (otherwise read-only). */
+ #define VRING_DESC_F_WRITE 2
+ /* This means the buffer contains a list of buffer descriptors. */
+ #define VRING_DESC_F_INDIRECT 4
+ /* The flags as indicated above. */
+ u16 flags;
+ /* Next field if flags & NEXT */
+ u16 next;
+ };
+
+The number of descriptors in the table is specified by the Queue
+Size field for this virtqueue.
+
+2.3.3 Indirect Descriptors
+
+Some devices benefit by concurrently dispatching a large number
+of large requests. The VIRTIO_RING_F_INDIRECT_DESC feature can be
+used to allow this (see Appendix B: Reserved Feature Bits). To increase
+ring capacity it is possible to store a table of indirect
+descriptors anywhere in memory, and insert a descriptor in main
+virtqueue (with flags&INDIRECT on) that refers to memory buffer
+containing this indirect descriptor table; fields addr and len
+refer to the indirect table address and length in bytes,
+respectively. The indirect table layout structure looks like this
+(len is the length of the descriptor that refers to this table,
+which is a variable, so this code won't compile):
+
+ struct indirect_descriptor_table {
+ /* The actual descriptors (16 bytes each) */
+ struct vring_desc desc[len / 16];
+ };
+
+The first indirect descriptor is located at start of the indirect
+descriptor table (index 0), additional indirect descriptors are
+chained by next field. An indirect descriptor without next field
+(with flags&NEXT off) signals the end of the indirect descriptor
+table, and transfers control back to the main virtqueue. An
+indirect descriptor can not refer to another indirect descriptor
+table (flags&INDIRECT must be off). A single indirect descriptor
+table can include both read-only and write-only descriptors;
+write-only flag (flags&WRITE) in the descriptor that refers to it
+is ignored.
+
+2.3.4 Available Ring
+
+The available ring refers to what descriptors we are offering the
+device: it refers to the head of a descriptor chain. The “flags” field
+is currently 0 or 1: 1 indicating that we do not need an interrupt
+when the device consumes a descriptor from the available
+ring. Alternatively, the guest can ask the device to delay interrupts
+until an entry with an index specified by the “ used_event” field is
+written in the used ring (equivalently, until the idx field in the
+used ring will reach the value used_event + 1). The method employed by
+the device is controlled by the VIRTIO_RING_F_EVENT_IDX feature bit
+(see Appendix B: Reserved Feature Bits). This interrupt suppression is
+merely an optimization; it may not suppress interrupts entirely.
+
+The “idx” field indicates where we would put the next descriptor
+entry (modulo the ring size). This starts at 0, and increases.
+
+ struct vring_avail {
+ #define VRING_AVAIL_F_NO_INTERRUPT 1
+ u16 flags;
+ u16 idx;
+ u16 ring[qsz]; /* qsz is the Queue Size field read from device */
+ u16 used_event;
+ };
+
+2.3.5 Used Ring
+
+The used ring is where the device returns buffers once it is done
+with them. The flags field can be used by the device to hint that
+no notification is necessary when the guest adds to the available
+ring. Alternatively, the “avail_event” field can be used by the
+device to hint that no notification is necessary until an entry
+with an index specified by the “avail_event” is written in the
+available ring (equivalently, until the idx field in the
+available ring will reach the value avail_event + 1). The method
+employed by the device is controlled by the guest through the
+VIRTIO_RING_F_EVENT_IDX feature bit (see Appendix B: Reserved
+Feature Bits).[7]
+
+Each entry in the ring is a pair: the head entry of the
+descriptor chain describing the buffer (this matches an entry
+placed in the available ring by the guest earlier), and the total
+of bytes written into the buffer. The latter is extremely useful
+for guests using untrusted buffers: if you do not know exactly
+how much has been written by the device, you usually have to zero
+the buffer to ensure no data leakage occurs.
+
+ /* u32 is used here for ids for padding reasons. */
+ struct vring_used_elem {
+ /* Index of start of used descriptor chain. */
+ u32 id;
+ /* Total length of the descriptor chain which was used (written to) */
+ u32 len;
+ };
+
+ struct vring_used {
+ #define VRING_USED_F_NO_NOTIFY 1
+ u16 flags;
+ u16 idx;
+ struct vring_used_elem ring[qsz];
+ u16 avail_event;
+ };
+
+2.3.6 Helpers for Managing Virtqueues
+
+The Linux Kernel Source code contains the definitions above and
+helper routines in a more usable form, in
+include/linux/virtio_ring.h. This was explicitly licensed by IBM
+and Red Hat under the (3-clause) BSD license so that it can be
+freely used by all other projects, and is reproduced (with slight
+variation to remove Linux assumptions) in Appendix A.
+
+2.4 Device Operation
+
+There are two parts to device operation: supplying new buffers to
+the device, and processing used buffers from the device. As an
+example, the virtio network device has two virtqueues: the
+transmit virtqueue and the receive virtqueue. The driver adds
+outgoing (read-only) packets to the transmit virtqueue, and then
+frees them after they are used. Similarly, incoming (write-only)
+buffers are added to the receive virtqueue, and processed after
+they are used.
+
+2.4.1 Supplying Buffers to The Device
+
+Actual transfer of buffers from the guest OS to the device
+operates as follows:
+
+1. Place the buffer(s) into free descriptor(s).
+
+ (a) If there are no free descriptors, the guest may choose to
+ notify the device even if notifications are suppressed (to
+ reduce latency).[8]
+
+2. Place the id of the buffer in the next ring entry of the
+ available ring.
+
+3. The steps (1) and (2) may be performed repeatedly if batching
+ is possible.
+
+4. A memory barrier should be executed to ensure the device sees
+ the updated descriptor table and available ring before the next
+ step.
+
+5. The available “idx” field should be increased by the number of
+ entries added to the available ring.
+
+6. A memory barrier should be executed to ensure that we update
+ the idx field before checking for notification suppression.
+
+7. If notifications are not suppressed, the device should be
+ notified of the new buffers.
+
+Note that the above code does not take precautions against the
+available ring buffer wrapping around: this is not possible since
+the ring buffer is the same size as the descriptor table, so step
+(1) will prevent such a condition.
+
+In addition, the maximum queue size is 32768 (it must be a power
+of 2 which fits in 16 bits), so the 16-bit “idx” value can always
+distinguish between a full and empty buffer.
+
+Here is a description of each stage in more detail.
+
+2.4.1.1 Placing Buffers Into The Descriptor Table
+
+A buffer consists of zero or more read-only physically-contiguous
+elements followed by zero or more physically-contiguous
+write-only elements (it must have at least one element). This
+algorithm maps it into the descriptor table:
+
+1. for each buffer element, b:
+
+ (a) Get the next free descriptor table entry, d
+
+ (b) Set d.addr to the physical address of the start of b
+
+ (c) Set d.len to the length of b.
+
+ (d) If b is write-only, set d.flags to VRING_DESC_F_WRITE,
+ otherwise 0.
+
+ (e) If there is a buffer element after this:
+
+ i. Set d.next to the index of the next free descriptor
+ element.
+
+ ii. Set the VRING_DESC_F_NEXT bit in d.flags.
+
+In practice, the d.next fields are usually used to chain free
+descriptors, and a separate count kept to check there are enough
+free descriptors before beginning the mappings.
+
+2.4.1.2 Updating The Available Ring
+
+The head of the buffer we mapped is the first d in the algorithm
+above. A naive implementation would do the following:
+
+ avail->ring[avail->idx % qsz] = head;
+
+However, in general we can add many descriptors before we update
+the “idx” field (at which point they become visible to the
+device), so we keep a counter of how many we've added:
+
+ avail->ring[(avail->idx + added++) % qsz] = head;
+
+2.4.1.3 Updating The Index Field
+
+Once the idx field of the virtqueue is updated, the device will
+be able to access the descriptor entries we've created and the
+memory they refer to. This is why a memory barrier is generally
+used before the idx update, to ensure it sees the most up-to-date
+copy.
+
+The idx field always increments, and we let it wrap naturally at
+65536:
+
+ avail->idx += added;
+
+2.4.1.4 Notifying The Device
+
+Device notification occurs by writing the 16-bit virtqueue index
+of this virtqueue to the Queue Notify field of the virtio header
+in the first I/O region of the PCI device. This can be expensive,
+however, so the device can suppress such notifications if it
+doesn't need them. We have to be careful to expose the new idx
+value before checking the suppression flag: it's OK to notify
+gratuitously, but not to omit a required notification. So again,
+we use a memory barrier here before reading the flags or the
+avail_event field.
+
+If the VIRTIO_F_RING_EVENT_IDX feature is not negotiated, and if
+the VRING_USED_F_NOTIFY flag is not set, we go ahead and write to
+the PCI configuration space.
+
+If the VIRTIO_F_RING_EVENT_IDX feature is negotiated, we read the
+avail_event field in the available ring structure. If the
+available index crossed_the avail_event field value since the
+last notification, we go ahead and write to the PCI configuration
+space. The avail_event field wraps naturally at 65536 as well:
+
+ (u16)(new_idx - avail_event - 1) < (u16)(new_idx - old_idx)
+
+2.4.2 Receiving Used Buffers From The Device
+
+Once the device has used a buffer (read from or written to it, or
+parts of both, depending on the nature of the virtqueue and the
+device), it sends an interrupt, following an algorithm very
+similar to the algorithm used for the driver to send the device a
+buffer:
+
+1. Write the head descriptor number to the next field in the used
+ ring.
+
+2. Update the used ring idx.
+
+3. Determine whether an interrupt is necessary:
+
+ (a) If the VIRTIO_F_RING_EVENT_IDX feature is not negotiated:
+ check if f the VRING_AVAIL_F_NO_INTERRUPT flag is not set in
+ avail->flags
+
+ (b) If the VIRTIO_F_RING_EVENT_IDX feature is negotiated: check
+ whether the used index crossed the used_event field value
+ since the last update. The used_event field wraps naturally
+ at 65536 as well:
+ (u16)(new_idx - used_event - 1) < (u16)(new_idx - old_idx)
+
+4. If an interrupt is necessary:
+
+ (a) If MSI-X capability is disabled:
+
+ i. Set the lower bit of the ISR Status field for the device.
+
+ ii. Send the appropriate PCI interrupt for the device.
+
+ (b) If MSI-X capability is enabled:
+
+ i. Request the appropriate MSI-X interrupt message for the
+ device, Queue Vector field sets the MSI-X Table entry
+ number.
+
+ ii. If Queue Vector field value is NO_VECTOR, no interrupt
+ message is requested for this event.
+
+The guest interrupt handler should:
+
+1. If MSI-X capability is disabled: read the ISR Status field,
+ which will reset it to zero. If the lower bit is zero, the
+ interrupt was not for this device. Otherwise, the guest driver
+ should look through the used rings of each virtqueue for the
+ device, to see if any progress has been made by the device
+ which requires servicing.
+
+2. If MSI-X capability is enabled: look through the used rings of
+ each virtqueue mapped to the specific MSI-X vector for the
+ device, to see if any progress has been made by the device
+ which requires servicing.
+
+For each ring, guest should then disable interrupts by writing
+VRING_AVAIL_F_NO_INTERRUPT flag in avail structure, if required.
+It can then process used ring entries finally enabling interrupts
+by clearing the VRING_AVAIL_F_NO_INTERRUPT flag or updating the
+EVENT_IDX field in the available structure, Guest should then
+execute a memory barrier, and then recheck the ring empty
+condition. This is necessary to handle the case where, after the
+last check and before enabling interrupts, an interrupt has been
+suppressed by the device:
+
+ vring_disable_interrupts(vq);
+
+ for (;;) {
+ if (vq->last_seen_used != vring->used.idx) {
+ vring_enable_interrupts(vq);
+ mb();
+
+ if (vq->last_seen_used != vring->used.idx)
+ break;
+ }
+
+ struct vring_used_elem *e = vring.used->ring[vq->last_seen_used%vsz];
+ process_buffer(e);
+ vq->last_seen_used++;
+ }
+
+2.4.3 Dealing With Configuration Changes
+
+Some virtio PCI devices can change the device configuration
+state, as reflected in the virtio header in the PCI configuration
+space. In this case:
+
+1. If MSI-X capability is disabled: an interrupt is delivered and
+ the second highest bit is set in the ISR Status field to
+ indicate that the driver should re-examine the configuration
+ space. Note that a single interrupt can indicate both that one
+ or more virtqueue has been used and that the configuration
+ space has changed: even if the config bit is set, virtqueues
+ must be scanned.
+
+2. If MSI-X capability is enabled: an interrupt message is
+ requested. The Configuration Vector field sets the MSI-X Table
+ entry number to use. If Configuration Vector field value is
+ NO_VECTOR, no interrupt message is requested for this event.
+
+
+Creating New Device Types
+
+Various considerations are necessary when creating a new device
+type:
+
+ How Many Virtqueues?
+
+It is possible that a very simple device will operate entirely
+through its configuration space, but most will need at least one
+virtqueue in which it will place requests. A device with both
+input and output (eg. console and network devices described here)
+need two queues: one which the driver fills with buffers to
+receive input, and one which the driver places buffers to
+transmit output.
+
+ What Configuration Space Layout?
+
+Configuration space is generally used for rarely-changing or
+initialization-time parameters. But it is a limited resource, so
+it might be better to use a virtqueue to update configuration
+information (the network device does this for filtering,
+otherwise the table in the config space could potentially be very
+large).
+
+Note that this space is generally the guest's native endian,
+rather than PCI's little-endian.
+
+ What Device Number?
+
+Currently device numbers are assigned quite freely: a simple
+request mail to the author of this document or the Linux
+virtualization mailing list[9] will be sufficient to secure a unique one.
+
+Meanwhile for experimental drivers, use 65535 and work backwards.
+
+ How many MSI-X vectors?
+
+Using the optional MSI-X capability devices can speed up
+interrupt processing by removing the need to read ISR Status
+register by guest driver (which might be an expensive operation),
+reducing interrupt sharing between devices and queues within the
+device, and handling interrupts from multiple CPUs. However, some
+systems impose a limit (which might be as low as 256) on the
+total number of MSI-X vectors that can be allocated to all
+devices. Devices and/or device drivers should take this into
+account, limiting the number of vectors used unless the device is
+expected to cause a high volume of interrupts. Devices can
+control the number of vectors used by limiting the MSI-X Table
+Size or not presenting MSI-X capability in PCI configuration
+space. Drivers can control this by mapping events to as small
+number of vectors as possible, or disabling MSI-X capability
+altogether.
+
+ Message Framing
+
+The descriptors used for a buffer should not effect the semantics
+of the message, except for the total length of the buffer. For
+example, a network buffer consists of a 10 byte header followed
+by the network packet. Whether this is presented in the ring
+descriptor chain as (say) a 10 byte buffer and a 1514 byte
+buffer, or a single 1524 byte buffer, or even three buffers,
+should have no effect.
+
+In particular, no implementation should use the descriptor
+boundaries to determine the size of any header in a request.[10]
+
+ Device Improvements
+
+Any change to configuration space, or new virtqueues, or
+behavioural changes, should be indicated by negotiation of a new
+feature bit. This establishes clarity[11] and avoids future expansion problems.
+
+Clusters of functionality which are always implemented together
+can use a single bit, but if one feature makes sense without the
+others they should not be gratuitously grouped together to
+conserve feature bits. We can always extend the spec when the
+first person needs more than 24 feature bits for their device.
+
+
+
+
+Appendix A: virtio_ring.h
+
+#ifndef VIRTIO_RING_H
+#define VIRTIO_RING_H
+/* An interface for efficient virtio implementation.
+ *
+ * This header is BSD licensed so anyone can use the definitions
+ * to implement compatible drivers/servers.
+ *
+ * Copyright 2007, 2009, IBM Corporation
+ * Copyright 2011, Red Hat, Inc
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of IBM nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL IBM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ */
+
+/* This marks a buffer as continuing via the next field. */
+#define VRING_DESC_F_NEXT 1
+/* This marks a buffer as write-only (otherwise read-only). */
+#define VRING_DESC_F_WRITE 2
+
+/* The Host uses this in used->flags to advise the Guest: don't kick me
+ * when you add a buffer. It's unreliable, so it's simply an
+ * optimization. Guest will still kick if it's out of buffers. */
+#define VRING_USED_F_NO_NOTIFY 1
+/* The Guest uses this in avail->flags to advise the Host: don't
+ * interrupt me when you consume a buffer. It's unreliable, so it's
+ * simply an optimization. */
+#define VRING_AVAIL_F_NO_INTERRUPT 1
+
+/* Virtio ring descriptors: 16 bytes.
+ * These can chain together via "next". */
+struct vring_desc {
+ /* Address (guest-physical). */
+ uint64_t addr;
+ /* Length. */
+ uint32_t len;
+ /* The flags as indicated above. */
+ uint16_t flags;
+ /* We chain unused descriptors via this, too */
+ uint16_t next;
+};
+
+struct vring_avail {
+ uint16_t flags;
+ uint16_t idx;
+ uint16_t ring[];
+ uint16_t used_event;
+};
+
+/* u32 is used here for ids for padding reasons. */
+struct vring_used_elem {
+ /* Index of start of used descriptor chain. */
+ uint32_t id;
+ /* Total length of the descriptor chain which was written to. */
+ uint32_t len;
+};
+
+struct vring_used {
+ uint16_t flags;
+ uint16_t idx;
+ struct vring_used_elem ring[];
+ uint16_t avail_event;
+};
+
+struct vring {
+ unsigned int num;
+
+ struct vring_desc *desc;
+ struct vring_avail *avail;
+ struct vring_used *used;
+};
+
+/* The standard layout for the ring is a continuous chunk of memory which
+ * looks like this. We assume num is a power of 2.
+ *
+ * struct vring {
+ * // The actual descriptors (16 bytes each)
+ * struct vring_desc desc[num];
+ *
+ * // A ring of available descriptor heads with free-running index.
+ * __u16 avail_flags;
+ * __u16 avail_idx;
+ * __u16 available[num];
+ *
+ * // Padding to the next align boundary.
+ * char pad[];
+ *
+ * // A ring of used descriptor heads with free-running index.
+ * __u16 used_flags;
+ * __u16 EVENT_IDX;
+ * struct vring_used_elem used[num];
+ * };
+ * Note: for virtio PCI, align is 4096.
+ */
+static inline void vring_init(struct vring *vr, unsigned int num, void *p,
+ unsigned long align)
+{
+ vr->num = num;
+ vr->desc = p;
+ vr->avail = p + num*sizeof(struct vring_desc);
+ vr->used = (void *)(((unsigned long)&vr->avail->ring[num]
+ + align-1)
+ & ~(align - 1));
+}
+
+static inline unsigned vring_size(unsigned int num, unsigned long align)
+{
+ return ((sizeof(struct vring_desc)*num + sizeof(uint16_t)*(2+num)
+ + align - 1) & ~(align - 1))
+ + sizeof(uint16_t)*3 + sizeof(struct vring_used_elem)*num;
+}
+
+static inline int vring_need_event(uint16_t event_idx, uint16_t new_idx, uint16_t old_idx)
+{
+ return (uint16_t)(new_idx - event_idx - 1) < (uint16_t)(new_idx - old_idx);
+}
+#endif /* VIRTIO_RING_H */
+
+
+Appendix B: Reserved Feature Bits
+
+Currently there are five device-independent feature bits defined:
+
+ VIRTIO_F_NOTIFY_ON_EMPTY (24) Negotiating this feature
+ indicates that the driver wants an interrupt if the device runs
+ out of available descriptors on a virtqueue, even though
+ interrupts are suppressed using the VRING_AVAIL_F_NO_INTERRUPT
+ flag or the used_event field. An example of this is the
+ networking driver: it doesn't need to know every time a packet
+ is transmitted, but it does need to free the transmitted
+ packets a finite time after they are transmitted. It can avoid
+ using a timer if the device interrupts it when all the packets
+ are transmitted.
+
+ VIRTIO_F_RING_INDIRECT_DESC (28) Negotiating this feature indicates
+ that the driver can use descriptors with the VRING_DESC_F_INDIRECT
+ flag set, as described in 2.3.3 Indirect Descriptors.
+
+ VIRTIO_F_RING_EVENT_IDX(29) This feature enables the used_event
+ and the avail_event fields. If set, it indicates that the
+ device should ignore the flags field in the available ring
+ structure. Instead, the used_event field in this structure is
+ used by guest to suppress device interrupts. Further, the
+ driver should ignore the flags field in the used ring
+ structure. Instead, the avail_event field in this structure is
+ used by the device to suppress notifications. If unset, the
+ driver should ignore the used_event field; the device should
+ ignore the avail_event field; the flags field is used
+
+Appendix C: Network Device
+
+The virtio network device is a virtual ethernet card, and is the
+most complex of the devices supported so far by virtio. It has
+enhanced rapidly and demonstrates clearly how support for new
+features should be added to an existing device. Empty buffers are
+placed in one virtqueue for receiving packets, and outgoing
+packets are enqueued into another for transmission in that order.
+A third command queue is used to control advanced filtering
+features.
+
+Configuration
+
+ Subsystem Device ID 1
+
+ Virtqueues 0:receiveq. 1:transmitq. 2:controlq[12]
+
+Feature bits
+
+ VIRTIO_NET_F_CSUM (0) Device handles packets with partial checksum
+
+ VIRTIO_NET_F_GUEST_CSUM (1) Guest handles packets with partial checksum
+
+ VIRTIO_NET_F_MAC (5) Device has given MAC address.
+
+ VIRTIO_NET_F_GSO (6) (Deprecated) device handles packets with
+ any GSO type.[13]
+
+ VIRTIO_NET_F_GUEST_TSO4 (7) Guest can receive TSOv4.
+
+ VIRTIO_NET_F_GUEST_TSO6 (8) Guest can receive TSOv6.
+
+ VIRTIO_NET_F_GUEST_ECN (9) Guest can receive TSO with ECN.
+
+ VIRTIO_NET_F_GUEST_UFO (10) Guest can receive UFO.
+
+ VIRTIO_NET_F_HOST_TSO4 (11) Device can receive TSOv4.
+
+ VIRTIO_NET_F_HOST_TSO6 (12) Device can receive TSOv6.
+
+ VIRTIO_NET_F_HOST_ECN (13) Device can receive TSO with ECN.
+
+ VIRTIO_NET_F_HOST_UFO (14) Device can receive UFO.
+
+ VIRTIO_NET_F_MRG_RXBUF (15) Guest can merge receive buffers.
+
+ VIRTIO_NET_F_STATUS (16) Configuration status field is
+ available.
+
+ VIRTIO_NET_F_CTRL_VQ (17) Control channel is available.
+
+ VIRTIO_NET_F_CTRL_RX (18) Control channel RX mode support.
+
+ VIRTIO_NET_F_CTRL_VLAN (19) Control channel VLAN filtering.
+
+ VIRTIO_NET_F_GUEST_ANNOUNCE(21) Guest can send gratuitous
+ packets.
+
+ Device configuration layout Two configuration fields are
+ currently defined. The mac address field always exists (though
+ is only valid if VIRTIO_NET_F_MAC is set), and the status field
+ only exists if VIRTIO_NET_F_STATUS is set. Two read-only bits
+ are currently defined for the status field:
+ VIRTIO_NET_S_LINK_UP and VIRTIO_NET_S_ANNOUNCE.
+
+ #define VIRTIO_NET_S_LINK_UP 1
+ #define VIRTIO_NET_S_ANNOUNCE 2
+
+ struct virtio_net_config {
+ u8 mac[6];
+ u16 status;
+ };
+
+Device Initialization
+
+1. The initialization routine should identify the receive and
+ transmission virtqueues.
+
+2. If the VIRTIO_NET_F_MAC feature bit is set, the configuration
+ space “mac” entry indicates the “physical” address of the the
+ network card, otherwise a private MAC address should be
+ assigned. All guests are expected to negotiate this feature if
+ it is set.
+
+3. If the VIRTIO_NET_F_CTRL_VQ feature bit is negotiated,
+ identify the control virtqueue.
+
+4. If the VIRTIO_NET_F_STATUS feature bit is negotiated, the link
+ status can be read from the bottom bit of the “status” config
+ field. Otherwise, the link should be assumed active.
+
+5. The receive virtqueue should be filled with receive buffers.
+ This is described in detail below in “Setting Up Receive
+ Buffers”.
+
+6. A driver can indicate that it will generate checksumless
+ packets by negotating the VIRTIO_NET_F_CSUM feature. This “
+ checksum offload” is a common feature on modern network cards.
+
+7. If that feature is negotiated[14], a driver can use TCP or UDP
+ segmentation offload by negotiating the VIRTIO_NET_F_HOST_TSO4 (IPv4
+ TCP), VIRTIO_NET_F_HOST_TSO6 (IPv6 TCP) and VIRTIO_NET_F_HOST_UFO
+ (UDP fragmentation) features. It should not send TCP packets
+ requiring segmentation offload which have the Explicit Congestion
+ Notification bit set, unless the VIRTIO_NET_F_HOST_ECN feature is
+ negotiated.[15]
+
+8. The converse features are also available: a driver can save
+ the virtual device some work by negotiating these features.[16]
+ The VIRTIO_NET_F_GUEST_CSUM feature indicates that partially
+ checksummed packets can be received, and if it can do that then
+ the VIRTIO_NET_F_GUEST_TSO4, VIRTIO_NET_F_GUEST_TSO6,
+ VIRTIO_NET_F_GUEST_UFO and VIRTIO_NET_F_GUEST_ECN are the input
+ equivalents of the features described above. See “Receiving
+ Packets” below.
+
+Device Operation
+
+Packets are transmitted by placing them in the transmitq, and
+buffers for incoming packets are placed in the receiveq. In each
+case, the packet itself is preceeded by a header:
+
+ struct virtio_net_hdr {
+ #define VIRTIO_NET_HDR_F_NEEDS_CSUM 1
+ u8 flags;
+ #define VIRTIO_NET_HDR_GSO_NONE 0
+ #define VIRTIO_NET_HDR_GSO_TCPV4 1
+ #define VIRTIO_NET_HDR_GSO_UDP 3
+ #define VIRTIO_NET_HDR_GSO_TCPV6 4
+ #define VIRTIO_NET_HDR_GSO_ECN 0x80
+ u8 gso_type;
+ u16 hdr_len;
+ u16 gso_size;
+ u16 csum_start;
+ u16 csum_offset;
+ /* Only if VIRTIO_NET_F_MRG_RXBUF: */
+ u16 num_buffers
+ };
+
+The controlq is used to control device features such as
+filtering.
+
+Packet Transmission
+
+Transmitting a single packet is simple, but varies depending on
+the different features the driver negotiated.
+
+1. If the driver negotiated VIRTIO_NET_F_CSUM, and the packet has
+ not been fully checksummed, then the virtio_net_hdr's fields
+ are set as follows. Otherwise, the packet must be fully
+ checksummed, and flags is zero.
+
+ • flags has the VIRTIO_NET_HDR_F_NEEDS_CSUM set,
+
+ • csum_start is set to the offset within the packet to begin checksumming,
+ and
+
+ • csum_offset indicates how many bytes after the csum_start the
+ new (16 bit ones' complement) checksum should be placed.[17]
+
+2. If the driver negotiated
+ VIRTIO_NET_F_HOST_TSO4, TSO6 or UFO, and the packet requires
+ TCP segmentation or UDP fragmentation, then the “gso_type”
+ field is set to VIRTIO_NET_HDR_GSO_TCPV4, TCPV6 or UDP.
+ (Otherwise, it is set to VIRTIO_NET_HDR_GSO_NONE). In this
+ case, packets larger than 1514 bytes can be transmitted: the
+ metadata indicates how to replicate the packet header to cut it
+ into smaller packets. The other gso fields are set:
+
+ • hdr_len is a hint to the device as to how much of the header
+ needs to be kept to copy into each packet, usually set to the
+ length of the headers, including the transport header.[18]
+
+ • gso_size is the maximum size of each packet beyond that
+ header (ie. MSS).
+
+ • If the driver negotiated the VIRTIO_NET_F_HOST_ECN feature,
+ the VIRTIO_NET_HDR_GSO_ECN bit may be set in “gso_type” as
+ well, indicating that the TCP packet has the ECN bit set.[19]
+
+3. If the driver negotiated the VIRTIO_NET_F_MRG_RXBUF feature,
+ the num_buffers field is set to zero.
+
+4. The header and packet are added as one output buffer to the
+ transmitq, and the device is notified of the new entry (see 2.4.1.4
+ Notifying The Device).[20]
+
+ Packet Transmission Interrupt
+
+Often a driver will suppress transmission interrupts using the
+VRING_AVAIL_F_NO_INTERRUPT flag (see 2.4.2 Receiving Used Buffers From
+The Device) and check for used packets in the transmit path of following
+packets. However, it will still receive interrupts if the
+VIRTIO_F_NOTIFY_ON_EMPTY feature is negotiated, indicating that
+the transmission queue is completely emptied.
+
+The normal behavior in this interrupt handler is to retrieve and
+new descriptors from the used ring and free the corresponding
+headers and packets.
+
+ Setting Up Receive Buffers
+
+It is generally a good idea to keep the receive virtqueue as
+fully populated as possible: if it runs out, network performance
+will suffer.
+
+If the VIRTIO_NET_F_GUEST_TSO4, VIRTIO_NET_F_GUEST_TSO6 or
+VIRTIO_NET_F_GUEST_UFO features are used, the Guest will need to
+accept packets of up to 65550 bytes long (the maximum size of a
+TCP or UDP packet, plus the 14 byte ethernet header), otherwise
+1514 bytes. So unless VIRTIO_NET_F_MRG_RXBUF is negotiated, every
+buffer in the receive queue needs to be at least this length [20a]
+
+If VIRTIO_NET_F_MRG_RXBUF is negotiated, each buffer must be at
+least the size of the struct virtio_net_hdr.
+
+ Packet Receive Interrupt
+
+When a packet is copied into a buffer in the receiveq, the
+optimal path is to disable further interrupts for the receiveq
+(see [sub:Receiving-Used-Buffers]) and process packets until no
+more are found, then re-enable them.
+
+Processing packet involves:
+
+1. If the driver negotiated the VIRTIO_NET_F_MRG_RXBUF feature,
+ then the “num_buffers” field indicates how many descriptors
+ this packet is spread over (including this one). This allows
+ receipt of large packets without having to allocate large
+ buffers. In this case, there will be at least “num_buffers” in
+ the used ring, and they should be chained together to form a
+ single packet. The other buffers will not begin with a struct
+ virtio_net_hdr.
+
+2. If the VIRTIO_NET_F_MRG_RXBUF feature was not negotiated, or
+ the “num_buffers” field is one, then the entire packet will be
+ contained within this buffer, immediately following the struct
+ virtio_net_hdr.
+
+3. If the VIRTIO_NET_F_GUEST_CSUM feature was negotiated, the
+ VIRTIO_NET_HDR_F_NEEDS_CSUM bit in the “flags” field may be
+ set: if so, the checksum on the packet is incomplete and the “
+ csum_start” and “csum_offset” fields indicate how to calculate
+ it (see Packet Transmission point 1).
+
+4. If the VIRTIO_NET_F_GUEST_TSO4, TSO6 or UFO options were
+ negotiated, then the “gso_type” may be something other than
+ VIRTIO_NET_HDR_GSO_NONE, and the “gso_size” field indicates the
+ desired MSS (see Packet Transmission point 2).
+
+Control Virtqueue
+
+The driver uses the control virtqueue (if VIRTIO_NET_F_VTRL_VQ is
+negotiated) to send commands to manipulate various features of
+the device which would not easily map into the configuration
+space.
+
+All commands are of the following form:
+
+ struct virtio_net_ctrl {
+ u8 class;
+ u8 command;
+ u8 command-specific-data[];
+ u8 ack;
+ };
+
+ /* ack values */
+ #define VIRTIO_NET_OK 0
+ #define VIRTIO_NET_ERR 1
+
+The class, command and command-specific-data are set by the
+driver, and the device sets the ack byte. There is little it can
+do except issue a diagnostic if the ack byte is not
+VIRTIO_NET_OK.
+
+Packet Receive Filtering
+
+If the VIRTIO_NET_F_CTRL_RX feature is negotiated, the driver can
+send control commands for promiscuous mode, multicast receiving,
+and filtering of MAC addresses.
+
+Note that in general, these commands are best-effort: unwanted
+packets may still arrive.
+
+Setting Promiscuous Mode
+
+ #define VIRTIO_NET_CTRL_RX 0
+ #define VIRTIO_NET_CTRL_RX_PROMISC 0
+ #define VIRTIO_NET_CTRL_RX_ALLMULTI 1
+
+The class VIRTIO_NET_CTRL_RX has two commands:
+VIRTIO_NET_CTRL_RX_PROMISC turns promiscuous mode on and off, and
+VIRTIO_NET_CTRL_RX_ALLMULTI turns all-multicast receive on and
+off. The command-specific-data is one byte containing 0 (off) or
+1 (on).
+
+Setting MAC Address Filtering
+
+ struct virtio_net_ctrl_mac {
+ u32 entries;
+ u8 macs[entries][ETH_ALEN];
+ };
+
+ #define VIRTIO_NET_CTRL_MAC 1
+ #define VIRTIO_NET_CTRL_MAC_TABLE_SET 0
+
+The device can filter incoming packets by any number of destination
+MAC addresses.[21] This table is set using the class
+VIRTIO_NET_CTRL_MAC and the command VIRTIO_NET_CTRL_MAC_TABLE_SET. The
+command-specific-data is two variable length tables of 6-byte MAC
+addresses. The first table contains unicast addresses, and the second
+contains multicast addresses.
+
+VLAN Filtering
+
+If the driver negotiates the VIRTION_NET_F_CTRL_VLAN feature, it
+can control a VLAN filter table in the device.
+
+ #define VIRTIO_NET_CTRL_VLAN 2
+ #define VIRTIO_NET_CTRL_VLAN_ADD 0
+ #define VIRTIO_NET_CTRL_VLAN_DEL 1
+
+Both the VIRTIO_NET_CTRL_VLAN_ADD and VIRTIO_NET_CTRL_VLAN_DEL
+command take a 16-bit VLAN id as the command-specific-data.
+
+Gratuitous Packet Sending
+
+If the driver negotiates the VIRTIO_NET_F_GUEST_ANNOUNCE (depends
+on VIRTIO_NET_F_CTRL_VQ), it can ask the guest to send gratuitous
+packets; this is usually done after the guest has been physically
+migrated, and needs to announce its presence on the new network
+links. (As hypervisor does not have the knowledge of guest
+network configuration (eg. tagged vlan) it is simplest to prod
+the guest in this way).
+
+ #define VIRTIO_NET_CTRL_ANNOUNCE 3
+ #define VIRTIO_NET_CTRL_ANNOUNCE_ACK 0
+
+The Guest needs to check VIRTIO_NET_S_ANNOUNCE bit in status
+field when it notices the changes of device configuration. The
+command VIRTIO_NET_CTRL_ANNOUNCE_ACK is used to indicate that
+driver has recevied the notification and device would clear the
+VIRTIO_NET_S_ANNOUNCE bit in the status filed after it received
+this command.
+
+Processing this notification involves:
+
+1. Sending the gratuitous packets or marking there are pending
+ gratuitous packets to be sent and letting deferred routine to
+ send them.
+
+2. Sending VIRTIO_NET_CTRL_ANNOUNCE_ACK command through control
+ vq.
+
+3. .
+
+Appendix D: Block Device
+
+The virtio block device is a simple virtual block device (ie.
+disk). Read and write requests (and other exotic requests) are
+placed in the queue, and serviced (probably out of order) by the
+device except where noted.
+
+Configuration
+
+ Subsystem Device ID 2
+
+ Virtqueues 0:requestq.
+
+ Feature bits
+
+ VIRTIO_BLK_F_BARRIER (0) Host supports request barriers.
+
+ VIRTIO_BLK_F_SIZE_MAX (1) Maximum size of any single segment is
+ in “size_max”.
+
+ VIRTIO_BLK_F_SEG_MAX (2) Maximum number of segments in a
+ request is in “seg_max”.
+
+ VIRTIO_BLK_F_GEOMETRY (4) Disk-style geometry specified in “
+ geometry”.
+
+ VIRTIO_BLK_F_RO (5) Device is read-only.
+
+ VIRTIO_BLK_F_BLK_SIZE (6) Block size of disk is in “blk_size”.
+
+ VIRTIO_BLK_F_SCSI (7) Device supports scsi packet commands.
+
+ VIRTIO_BLK_F_FLUSH (9) Cache flush command support.
+
+ Device configuration layout The capacity of the device
+ (expressed in 512-byte sectors) is always present. The
+ availability of the others all depend on various feature bits
+ as indicated above.
+
+ struct virtio_blk_config {
+ u64 capacity;
+ u32 size_max;
+ u32 seg_max;
+ struct virtio_blk_geometry {
+ u16 cylinders;
+ u8 heads;
+ u8 sectors;
+ } geometry;
+ u32 blk_size;
+ };
+
+Device Initialization
+
+1. The device size should be read from the “capacity”
+ configuration field. No requests should be submitted which goes
+ beyond this limit.
+
+2. If the VIRTIO_BLK_F_BLK_SIZE feature is negotiated, the
+ blk_size field can be read to determine the optimal sector size
+ for the driver to use. This does not effect the units used in
+ the protocol (always 512 bytes), but awareness of the correct
+ value can effect performance.
+
+3. If the VIRTIO_BLK_F_RO feature is set by the device, any write
+ requests will fail.
+
+Device Operation
+
+The driver queues requests to the virtqueue, and they are used by
+the device (not necessarily in order). Each request is of form:
+
+ struct virtio_blk_req {
+ u32 type;
+ u32 ioprio;
+ u64 sector;
+ char data[][512];
+ u8 status;
+ };
+
+If the device has VIRTIO_BLK_F_SCSI feature, it can also support
+scsi packet command requests, each of these requests is of form:
+
+ struct virtio_scsi_pc_req {
+ u32 type;
+ u32 ioprio;
+ u64 sector;
+ char cmd[];
+ char data[][512];
+#define SCSI_SENSE_BUFFERSIZE 96
+ u8 sense[SCSI_SENSE_BUFFERSIZE];
+ u32 errors;
+ u32 data_len;
+ u32 sense_len;
+ u32 residual;
+ u8 status;
+ };
+
+The type of the request is either a read (VIRTIO_BLK_T_IN), a write
+(VIRTIO_BLK_T_OUT), a scsi packet command (VIRTIO_BLK_T_SCSI_CMD or
+VIRTIO_BLK_T_SCSI_CMD_OUT[22]) or a flush (VIRTIO_BLK_T_FLUSH or
+VIRTIO_BLK_T_FLUSH_OUT[23]). If the device has VIRTIO_BLK_F_BARRIER
+feature the high bit (VIRTIO_BLK_T_BARRIER) indicates that this
+request acts as a barrier and that all preceeding requests must be
+complete before this one, and all following requests must not be
+started until this is complete. Note that a barrier does not flush
+caches in the underlying backend device in host, and thus does not
+serve as data consistency guarantee. Driver must use FLUSH request to
+flush the host cache.
+
+ #define VIRTIO_BLK_T_IN 0
+ #define VIRTIO_BLK_T_OUT 1
+ #define VIRTIO_BLK_T_SCSI_CMD 2
+ #define VIRTIO_BLK_T_SCSI_CMD_OUT 3
+ #define VIRTIO_BLK_T_FLUSH 4
+ #define VIRTIO_BLK_T_FLUSH_OUT 5
+ #define VIRTIO_BLK_T_BARRIER 0x80000000
+
+The ioprio field is a hint about the relative priorities of
+requests to the device: higher numbers indicate more important
+requests.
+
+The sector number indicates the offset (multiplied by 512) where
+the read or write is to occur. This field is unused and set to 0
+for scsi packet commands and for flush commands.
+
+The cmd field is only present for scsi packet command requests,
+and indicates the command to perform. This field must reside in a
+single, separate read-only buffer; command length can be derived
+from the length of this buffer.
+
+Note that these first three (four for scsi packet commands)
+fields are always read-only: the data field is either read-only
+or write-only, depending on the request. The size of the read or
+write can be derived from the total size of the request buffers.
+
+The sense field is only present for scsi packet command requests,
+and indicates the buffer for scsi sense data.
+
+The data_len field is only present for scsi packet command
+requests, this field is deprecated, and should be ignored by the
+driver. Historically, devices copied data length there.
+
+The sense_len field is only present for scsi packet command
+requests and indicates the number of bytes actually written to
+the sense buffer.
+
+The residual field is only present for scsi packet command
+requests and indicates the residual size, calculated as data
+length - number of bytes actually transferred.
+
+The final status byte is written by the device: either
+VIRTIO_BLK_S_OK for success, VIRTIO_BLK_S_IOERR for host or guest
+error or VIRTIO_BLK_S_UNSUPP for a request unsupported by host:
+
+ #define VIRTIO_BLK_S_OK 0
+ #define VIRTIO_BLK_S_IOERR 1
+ #define VIRTIO_BLK_S_UNSUPP 2
+
+Historically, devices assumed that the fields type, ioprio and
+sector reside in a single, separate read-only buffer; the fields
+errors, data_len, sense_len and residual reside in a single,
+separate write-only buffer; the sense field in a separate
+write-only buffer of size 96 bytes, by itself; the fields errors,
+data_len, sense_len and residual in a single write-only buffer;
+and the status field is a separate read-only buffer of size 1
+byte, by itself.
+
+Appendix E: Console Device
+
+The virtio console device is a simple device for data input and
+output. A device may have one or more ports. Each port has a pair
+of input and output virtqueues. Moreover, a device has a pair of
+control IO virtqueues. The control virtqueues are used to
+communicate information between the device and the driver about
+ports being opened and closed on either side of the connection,
+indication from the host about whether a particular port is a
+console port, adding new ports, port hot-plug/unplug, etc., and
+indication from the guest about whether a port or a device was
+successfully added, port open/close, etc.. For data IO, one or
+more empty buffers are placed in the receive queue for incoming
+data and outgoing characters are placed in the transmit queue.
+
+Configuration
+
+ Subsystem Device ID 3
+
+ Virtqueues 0:receiveq(port0). 1:transmitq(port0), 2:control
+ receiveq[24], 3:control transmitq, 4:receiveq(port1), 5:transmitq(port1),
+ ...
+
+ Feature bits
+
+ VIRTIO_CONSOLE_F_SIZE (0) Configuration cols and rows fields
+ are valid.
+
+ VIRTIO_CONSOLE_F_MULTIPORT(1) Device has support for multiple
+ ports; configuration fields nr_ports and max_nr_ports are
+ valid and control virtqueues will be used.
+
+ Device configuration layout The size of the console is supplied
+ in the configuration space if the VIRTIO_CONSOLE_F_SIZE feature
+ is set. Furthermore, if the VIRTIO_CONSOLE_F_MULTIPORT feature
+ is set, the maximum number of ports supported by the device can
+ be fetched.
+
+ struct virtio_console_config {
+ u16 cols;
+ u16 rows;
+ u32 max_nr_ports;
+ };
+
+Device Initialization
+
+1. If the VIRTIO_CONSOLE_F_SIZE feature is negotiated, the driver
+ can read the console dimensions from the configuration fields.
+
+2. If the VIRTIO_CONSOLE_F_MULTIPORT feature is negotiated, the
+ driver can spawn multiple ports, not all of which may be
+ attached to a console. Some could be generic ports. In this
+ case, the control virtqueues are enabled and according to the
+ max_nr_ports configuration-space value, the appropriate number
+ of virtqueues are created. A control message indicating the
+ driver is ready is sent to the host. The host can then send
+ control messages for adding new ports to the device. After
+ creating and initializing each port, a
+ VIRTIO_CONSOLE_PORT_READY control message is sent to the host
+ for that port so the host can let us know of any additional
+ configuration options set for that port.
+
+3. The receiveq for each port is populated with one or more
+ receive buffers.
+
+Device Operation
+
+1. For output, a buffer containing the characters is placed in
+ the port's transmitq.[25]
+
+2. When a buffer is used in the receiveq (signalled by an
+ interrupt), the contents is the input to the port associated
+ with the virtqueue for which the notification was received.
+
+3. If the driver negotiated the VIRTIO_CONSOLE_F_SIZE feature, a
+ configuration change interrupt may occur. The updated size can
+ be read from the configuration fields.
+
+4. If the driver negotiated the VIRTIO_CONSOLE_F_MULTIPORT
+ feature, active ports are announced by the host using the
+ VIRTIO_CONSOLE_PORT_ADD control message. The same message is
+ used for port hot-plug as well.
+
+5. If the host specified a port `name', a sysfs attribute is
+ created with the name filled in, so that udev rules can be
+ written that can create a symlink from the port's name to the
+ char device for port discovery by applications in the guest.
+
+6. Changes to ports' state are effected by control messages.
+ Appropriate action is taken on the port indicated in the
+ control message. The layout of the structure of the control
+ buffer and the events associated are:
+
+ struct virtio_console_control {
+ uint32_t id; /* Port number */
+ uint16_t event; /* The kind of control event */
+ uint16_t value; /* Extra information for the event */
+ };
+
+ /* Some events for the internal messages (control packets) */
+ #define VIRTIO_CONSOLE_DEVICE_READY 0
+ #define VIRTIO_CONSOLE_PORT_ADD 1
+ #define VIRTIO_CONSOLE_PORT_REMOVE 2
+ #define VIRTIO_CONSOLE_PORT_READY 3
+ #define VIRTIO_CONSOLE_CONSOLE_PORT 4
+ #define VIRTIO_CONSOLE_RESIZE 5
+ #define VIRTIO_CONSOLE_PORT_OPEN 6
+ #define VIRTIO_CONSOLE_PORT_NAME 7
+
+Appendix F: Entropy Device
+
+The virtio entropy device supplies high-quality randomness for
+guest use.
+
+ Configuration
+
+ Subsystem Device ID 4
+
+ Virtqueues 0:requestq.
+
+ Feature bits None currently defined
+
+ Device configuration layout None currently defined.
+
+Device Initialization
+
+1. The virtqueue is initialized
+
+Device Operation
+
+When the driver requires random bytes, it places the descriptor
+of one or more buffers in the queue. It will be completely filled
+by random data by the device.
+
+Appendix G: Memory Balloon Device
+
+The virtio memory balloon device is a primitive device for
+managing guest memory: the device asks for a certain amount of
+memory, and the guest supplies it (or withdraws it, if the device
+has more than it asks for). This allows the guest to adapt to
+changes in allowance of underlying physical memory. If the
+feature is negotiated, the device can also be used to communicate
+guest memory statistics to the host.
+
+ Configuration
+
+ Subsystem Device ID 5
+
+ Virtqueues 0:inflateq. 1:deflateq. 2:statsq.[26]
+
+ Feature bits
+
+ VIRTIO_BALLOON_F_MUST_TELL_HOST (0) Host must be told before
+ pages from the balloon are used.
+
+ VIRTIO_BALLOON_F_STATS_VQ (1) A virtqueue for reporting guest
+ memory statistics is present.
+
+ Device configuration layout Both fields of this configuration
+ are always available. Note that they are little endian, despite
+ convention that device fields are guest endian:
+
+ struct virtio_balloon_config {
+ u32 num_pages;
+ u32 actual;
+ };
+
+Device Initialization
+
+1. The inflate and deflate virtqueues are identified.
+
+2. If the VIRTIO_BALLOON_F_STATS_VQ feature bit is negotiated:
+
+ (a) Identify the stats virtqueue.
+
+ (b) Add one empty buffer to the stats virtqueue and notify the
+ host.
+
+Device operation begins immediately.
+
+Device Operation
+
+Memory Ballooning The device is driven by the receipt of a
+configuration change interrupt.
+
+1. The “num_pages” configuration field is examined. If this is
+ greater than the “actual” number of pages, memory must be given
+ to the balloon. If it is less than the “actual” number of
+ pages, memory may be taken back from the balloon for general
+ use.
+
+2. To supply memory to the balloon (aka. inflate):
+
+ (a) The driver constructs an array of addresses of unused memory
+ pages. These addresses are divided by 4096[27] and the descriptor
+ describing the resulting 32-bit array is added to the inflateq.
+
+3. To remove memory from the balloon (aka. deflate):
+
+ (a) The driver constructs an array of addresses of memory pages
+ it has previously given to the balloon, as described above.
+ This descriptor is added to the deflateq.
+
+ (b) If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is set, the
+ guest may not use these requested pages until that descriptor
+ in the deflateq has been used by the device.
+
+ (c) Otherwise, the guest may begin to re-use pages previously
+ given to the balloon before the device has acknowledged their
+ withdrawl. [28]
+
+4. In either case, once the device has completed the inflation or
+ deflation, the “actual” field of the configuration should be
+ updated to reflect the new number of pages in the balloon.[29]
+
+Memory Statistics
+
+The stats virtqueue is atypical because communication is driven
+by the device (not the driver). The channel becomes active at
+driver initialization time when the driver adds an empty buffer
+and notifies the device. A request for memory statistics proceeds
+as follows:
+
+1. The device pushes the buffer onto the used ring and sends an
+ interrupt.
+
+2. The driver pops the used buffer and discards it.
+
+3. The driver collects memory statistics and writes them into a
+ new buffer.
+
+4. The driver adds the buffer to the virtqueue and notifies the
+ device.
+
+5. The device pops the buffer (retaining it to initiate a
+ subsequent request) and consumes the statistics.
+
+ Memory Statistics Format Each statistic consists of a 16 bit
+ tag and a 64 bit value. Both quantities are represented in the
+ native endian of the guest. All statistics are optional and the
+ driver may choose which ones to supply. To guarantee backwards
+ compatibility, unsupported statistics should be omitted.
+
+ struct virtio_balloon_stat {
+ #define VIRTIO_BALLOON_S_SWAP_IN 0
+ #define VIRTIO_BALLOON_S_SWAP_OUT 1
+ #define VIRTIO_BALLOON_S_MAJFLT 2
+ #define VIRTIO_BALLOON_S_MINFLT 3
+ #define VIRTIO_BALLOON_S_MEMFREE 4
+ #define VIRTIO_BALLOON_S_MEMTOT 5
+ u16 tag;
+ u64 val;
+ } __attribute__((packed));
+
+ Tags
+
+ VIRTIO_BALLOON_S_SWAP_IN The amount of memory that has been
+ swapped in (in bytes).
+
+ VIRTIO_BALLOON_S_SWAP_OUT The amount of memory that has been
+ swapped out to disk (in bytes).
+
+ VIRTIO_BALLOON_S_MAJFLT The number of major page faults that
+ have occurred.
+
+ VIRTIO_BALLOON_S_MINFLT The number of minor page faults that
+ have occurred.
+
+ VIRTIO_BALLOON_S_MEMFREE The amount of memory not being used
+ for any purpose (in bytes).
+
+ VIRTIO_BALLOON_S_MEMTOT The total amount of memory available
+ (in bytes).
+
+Appendix I: SCSI Host Device
+
+The virtio SCSI host device groups together one or more virtual
+logical units (such as disks), and allows communicating to them
+using the SCSI protocol. An instance of the device represents a
+SCSI host to which many targets and LUNs are attached.
+
+The virtio SCSI device services two kinds of requests:
+
+• command requests for a logical unit;
+
+• task management functions related to a logical unit, target or
+ command.
+
+The device is also able to send out notifications about added and
+removed logical units. Together, these capabilities provide a
+SCSI transport protocol that uses virtqueues as the transfer
+medium. In the transport protocol, the virtio driver acts as the
+initiator, while the virtio SCSI host provides one or more
+targets that receive and process the requests.
+
+ Configuration
+
+ Subsystem Device ID 8
+
+ Virtqueues 0:controlq; 1:eventq; 2..n:request queues.
+
+ Feature bits
+
+ VIRTIO_SCSI_F_INOUT (0) A single request can include both
+ read-only and write-only data buffers.
+
+ VIRTIO_SCSI_F_HOTPLUG (1) The host should enable
+ hot-plug/hot-unplug of new LUNs and targets on the SCSI bus.
+
+ Device configuration layout All fields of this configuration
+ are always available. sense_size and cdb_size are writable by
+ the guest.
+
+ struct virtio_scsi_config {
+ u32 num_queues;
+ u32 seg_max;
+ u32 max_sectors;
+ u32 cmd_per_lun;
+ u32 event_info_size;
+ u32 sense_size;
+ u32 cdb_size;
+ u16 max_channel;
+ u16 max_target;
+ u32 max_lun;
+ };
+
+ num_queues is the total number of request virtqueues exposed by
+ the device. The driver is free to use only one request queue,
+ or it can use more to achieve better performance.
+
+ seg_max is the maximum number of segments that can be in a
+ command. A bidirectional command can include seg_max input
+ segments and seg_max output segments.
+
+ max_sectors is a hint to the guest about the maximum transfer
+ size it should use.
+
+ cmd_per_lun is a hint to the guest about the maximum number of
+ linked commands it should send to one LUN. The actual value
+ to be used is the minimum of cmd_per_lun and the virtqueue
+ size.
+
+ event_info_size is the maximum size that the device will fill
+ for buffers that the driver places in the eventq. The driver
+ should always put buffers at least of this size. It is
+ written by the device depending on the set of negotated
+ features.
+
+ sense_size is the maximum size of the sense data that the
+ device will write. The default value is written by the device
+ and will always be 96, but the driver can modify it. It is
+ restored to the default when the device is reset.
+
+ cdb_size is the maximum size of the CDB that the driver will
+ write. The default value is written by the device and will
+ always be 32, but the driver can likewise modify it. It is
+ restored to the default when the device is reset.
+
+ max_channel, max_target and max_lun can be used by the driver
+ as hints to constrain scanning the logical units on the
+ host.h
+
+Device Initialization
+
+The initialization routine should first of all discover the
+device's virtqueues.
+
+If the driver uses the eventq, it should then place at least a
+buffer in the eventq.
+
+The driver can immediately issue requests (for example, INQUIRY
+or REPORT LUNS) or task management functions (for example, I_T
+RESET).
+
+Device Operation: request queues
+
+The driver queues requests to an arbitrary request queue, and
+they are used by the device on that same queue. It is the
+responsibility of the driver to ensure strict request ordering
+for commands placed on different queues, because they will be
+consumed with no order constraints.
+
+Requests have the following format:
+
+ struct virtio_scsi_req_cmd {
+ // Read-only
+ u8 lun[8];
+ u64 id;
+ u8 task_attr;
+ u8 prio;
+ u8 crn;
+ char cdb[cdb_size];
+ char dataout[];
+ // Write-only part
+ u32 sense_len;
+ u32 residual;
+ u16 status_qualifier;
+ u8 status;
+ u8 response;
+ u8 sense[sense_size];
+ char datain[];
+ };
+
+
+ /* command-specific response values */
+ #define VIRTIO_SCSI_S_OK 0
+ #define VIRTIO_SCSI_S_OVERRUN 1
+ #define VIRTIO_SCSI_S_ABORTED 2
+ #define VIRTIO_SCSI_S_BAD_TARGET 3
+ #define VIRTIO_SCSI_S_RESET 4
+ #define VIRTIO_SCSI_S_BUSY 5
+ #define VIRTIO_SCSI_S_TRANSPORT_FAILURE 6
+ #define VIRTIO_SCSI_S_TARGET_FAILURE 7
+ #define VIRTIO_SCSI_S_NEXUS_FAILURE 8
+ #define VIRTIO_SCSI_S_FAILURE 9
+
+ /* task_attr */
+ #define VIRTIO_SCSI_S_SIMPLE 0
+ #define VIRTIO_SCSI_S_ORDERED 1
+ #define VIRTIO_SCSI_S_HEAD 2
+ #define VIRTIO_SCSI_S_ACA 3
+
+The lun field addresses a target and logical unit in the
+virtio-scsi device's SCSI domain. The only supported format for
+the LUN field is: first byte set to 1, second byte set to target,
+third and fourth byte representing a single level LUN structure,
+followed by four zero bytes. With this representation, a
+virtio-scsi device can serve up to 256 targets and 16384 LUNs per
+target.
+
+The id field is the command identifier (“tag”).
+
+task_attr, prio and crn should be left to zero. task_attr defines
+the task attribute as in the table above, but all task attributes
+may be mapped to SIMPLE by the device; crn may also be provided
+by clients, but is generally expected to be 0. The maximum CRN
+value defined by the protocol is 255, since CRN is stored in an
+8-bit integer.
+
+All of these fields are defined in SAM. They are always
+read-only, as are the cdb and dataout field. The cdb_size is
+taken from the configuration space.
+
+sense and subsequent fields are always write-only. The sense_len
+field indicates the number of bytes actually written to the sense
+buffer. The residual field indicates the residual size,
+calculated as “data_length - number_of_transferred_bytes”, for
+read or write operations. For bidirectional commands, the
+number_of_transferred_bytes includes both read and written bytes.
+A residual field that is less than the size of datain means that
+the dataout field was processed entirely. A residual field that
+exceeds the size of datain means that the dataout field was
+processed partially and the datain field was not processed at
+all.
+
+The status byte is written by the device to be the status code as
+defined in SAM.
+
+The response byte is written by the device to be one of the
+following:
+
+ VIRTIO_SCSI_S_OK when the request was completed and the status
+ byte is filled with a SCSI status code (not necessarily
+ "GOOD").
+
+ VIRTIO_SCSI_S_OVERRUN if the content of the CDB requires
+ transferring more data than is available in the data buffers.
+
+ VIRTIO_SCSI_S_ABORTED if the request was cancelled due to an
+ ABORT TASK or ABORT TASK SET task management function.
+
+ VIRTIO_SCSI_S_BAD_TARGET if the request was never processed
+ because the target indicated by the lun field does not exist.
+
+ VIRTIO_SCSI_S_RESET if the request was cancelled due to a bus
+ or device reset (including a task management function).
+
+ VIRTIO_SCSI_S_TRANSPORT_FAILURE if the request failed due to a
+ problem in the connection between the host and the target
+ (severed link).
+
+ VIRTIO_SCSI_S_TARGET_FAILURE if the target is suffering a
+ failure and the guest should not retry on other paths.
+
+ VIRTIO_SCSI_S_NEXUS_FAILURE if the nexus is suffering a failure
+ but retrying on other paths might yield a different result.
+
+ VIRTIO_SCSI_S_BUSY if the request failed but retrying on the
+ same path should work.
+
+ VIRTIO_SCSI_S_FAILURE for other host or guest error. In
+ particular, if neither dataout nor datain is empty, and the
+ VIRTIO_SCSI_F_INOUT feature has not been negotiated, the
+ request will be immediately returned with a response equal to
+ VIRTIO_SCSI_S_FAILURE.
+
+Device Operation: controlq
+
+The controlq is used for other SCSI transport operations.
+Requests have the following format:
+
+ struct virtio_scsi_ctrl {
+ u32 type;
+ ...
+ u8 response;
+ };
+
+ /* response values valid for all commands */
+ #define VIRTIO_SCSI_S_OK 0
+ #define VIRTIO_SCSI_S_BAD_TARGET 3
+ #define VIRTIO_SCSI_S_BUSY 5
+ #define VIRTIO_SCSI_S_TRANSPORT_FAILURE 6
+ #define VIRTIO_SCSI_S_TARGET_FAILURE 7
+ #define VIRTIO_SCSI_S_NEXUS_FAILURE 8
+ #define VIRTIO_SCSI_S_FAILURE 9
+ #define VIRTIO_SCSI_S_INCORRECT_LUN 12
+
+The type identifies the remaining fields.
+
+The following commands are defined:
+
+ Task management function
+ #define VIRTIO_SCSI_T_TMF 0
+
+ #define VIRTIO_SCSI_T_TMF_ABORT_TASK 0
+ #define VIRTIO_SCSI_T_TMF_ABORT_TASK_SET 1
+ #define VIRTIO_SCSI_T_TMF_CLEAR_ACA 2
+ #define VIRTIO_SCSI_T_TMF_CLEAR_TASK_SET 3
+ #define VIRTIO_SCSI_T_TMF_I_T_NEXUS_RESET 4
+ #define VIRTIO_SCSI_T_TMF_LOGICAL_UNIT_RESET 5
+ #define VIRTIO_SCSI_T_TMF_QUERY_TASK 6
+ #define VIRTIO_SCSI_T_TMF_QUERY_TASK_SET 7
+
+ struct virtio_scsi_ctrl_tmf
+ {
+ // Read-only part
+ u32 type;
+ u32 subtype;
+ u8 lun[8];
+ u64 id;
+ // Write-only part
+ u8 response;
+ }
+
+ /* command-specific response values */
+ #define VIRTIO_SCSI_S_FUNCTION_COMPLETE 0
+ #define VIRTIO_SCSI_S_FUNCTION_SUCCEEDED 10
+ #define VIRTIO_SCSI_S_FUNCTION_REJECTED 11
+
+ The type is VIRTIO_SCSI_T_TMF; the subtype field defines. All
+ fields except response are filled by the driver. The subtype
+ field must always be specified and identifies the requested
+ task management function.
+
+ Other fields may be irrelevant for the requested TMF; if so,
+ they are ignored but they should still be present. The lun
+ field is in the same format specified for request queues; the
+ single level LUN is ignored when the task management function
+ addresses a whole I_T nexus. When relevant, the value of the id
+ field is matched against the id values passed on the requestq.
+
+ The outcome of the task management function is written by the
+ device in the response field. The command-specific response
+ values map 1-to-1 with those defined in SAM.
+
+ Asynchronous notification query
+
+ #define VIRTIO_SCSI_T_AN_QUERY 1
+
+ struct virtio_scsi_ctrl_an {
+ // Read-only part
+ u32 type;
+ u8 lun[8];
+ u32 event_requested;
+ // Write-only part
+ u32 event_actual;
+ u8 response;
+ }
+
+ #define VIRTIO_SCSI_EVT_ASYNC_OPERATIONAL_CHANGE 2
+ #define VIRTIO_SCSI_EVT_ASYNC_POWER_MGMT 4
+ #define VIRTIO_SCSI_EVT_ASYNC_EXTERNAL_REQUEST 8
+ #define VIRTIO_SCSI_EVT_ASYNC_MEDIA_CHANGE 16
+ #define VIRTIO_SCSI_EVT_ASYNC_MULTI_HOST 32
+ #define VIRTIO_SCSI_EVT_ASYNC_DEVICE_BUSY 64
+
+ By sending this command, the driver asks the device which
+ events the given LUN can report, as described in paragraphs 6.6
+ and A.6 of the SCSI MMC specification. The driver writes the
+ events it is interested in into the event_requested; the device
+ responds by writing the events that it supports into
+ event_actual.
+
+ The type is VIRTIO_SCSI_T_AN_QUERY. The lun and event_requested
+ fields are written by the driver. The event_actual and response
+ fields are written by the device.
+
+ No command-specific values are defined for the response byte.
+
+ Asynchronous notification subscription
+ #define VIRTIO_SCSI_T_AN_SUBSCRIBE 2
+
+ struct virtio_scsi_ctrl_an {
+ // Read-only part
+ u32 type;
+ u8 lun[8];
+ u32 event_requested;
+ // Write-only part
+ u32 event_actual;
+ u8 response;
+ }
+
+ By sending this command, the driver asks the specified LUN to
+ report events for its physical interface, again as described in
+ the SCSI MMC specification. The driver writes the events it is
+ interested in into the event_requested; the device responds by
+ writing the events that it supports into event_actual.
+
+ Event types are the same as for the asynchronous notification
+ query message.
+
+ The type is VIRTIO_SCSI_T_AN_SUBSCRIBE. The lun and
+ event_requested fields are written by the driver. The
+ event_actual and response fields are written by the device.
+
+ No command-specific values are defined for the response byte.
+
+Device Operation: eventq
+
+The eventq is used by the device to report information on logical
+units that are attached to it. The driver should always leave a
+few buffers ready in the eventq. In general, the device will not
+queue events to cope with an empty eventq, and will end up
+dropping events if it finds no buffer ready. However, when
+reporting events for many LUNs (e.g. when a whole target
+disappears), the device can throttle events to avoid dropping
+them. For this reason, placing 10-15 buffers on the event queue
+should be enough.
+
+Buffers are placed in the eventq and filled by the device when
+interesting events occur. The buffers should be strictly
+write-only (device-filled) and the size of the buffers should be
+at least the value given in the device's configuration
+information.
+
+Buffers returned by the device on the eventq will be referred to
+as "events" in the rest of this section. Events have the
+following format:
+
+ #define VIRTIO_SCSI_T_EVENTS_MISSED 0x80000000
+
+ struct virtio_scsi_event {
+ // Write-only part
+ u32 event;
+ ...
+ }
+
+If bit 31 is set in the event field, the device failed to report
+an event due to missing buffers. In this case, the driver should
+poll the logical units for unit attention conditions, and/or do
+whatever form of bus scan is appropriate for the guest operating
+system.
+
+Other data that the device writes to the buffer depends on the
+contents of the event field. The following events are defined:
+
+ No event
+ #define VIRTIO_SCSI_T_NO_EVENT 0
+
+ This event is fired in the following cases:
+
+ • When the device detects in the eventq a buffer that is
+ shorter than what is indicated in the configuration field, it
+ might use it immediately and put this dummy value in the
+ event field. A well-written driver will never observe this
+ situation.
+
+ • When events are dropped, the device may signal this event as
+ soon as the drivers makes a buffer available, in order to
+ request action from the driver. In this case, of course, this
+ event will be reported with the VIRTIO_SCSI_T_EVENTS_MISSED
+ flag.
+
+ Transport reset
+ #define VIRTIO_SCSI_T_TRANSPORT_RESET 1
+
+ struct virtio_scsi_event_reset {
+ // Write-only part
+ u32 event;
+ u8 lun[8];
+ u32 reason;
+ }
+
+ #define VIRTIO_SCSI_EVT_RESET_HARD 0
+ #define VIRTIO_SCSI_EVT_RESET_RESCAN 1
+ #define VIRTIO_SCSI_EVT_RESET_REMOVED 2
+
+ By sending this event, the device signals that a logical unit
+ on a target has been reset, including the case of a new device
+ appearing or disappearing on the bus.The device fills in all
+ fields. The event field is set to
+ VIRTIO_SCSI_T_TRANSPORT_RESET. The lun field addresses a
+ logical unit in the SCSI host.
+
+ The reason value is one of the three #define values appearing
+ above:
+
+ • VIRTIO_SCSI_EVT_RESET_REMOVED (“LUN/target removed”) is used
+ if the target or logical unit is no longer able to receive
+ commands.
+
+ • VIRTIO_SCSI_EVT_RESET_HARD (“LUN hard reset”) is used if the
+ logical unit has been reset, but is still present.
+
+ • VIRTIO_SCSI_EVT_RESET_RESCAN (“rescan LUN/target”) is used if
+ a target or logical unit has just appeared on the device.
+
+ The “removed” and “rescan” events, when sent for LUN 0, may
+ apply to the entire target. After receiving them the driver
+ should ask the initiator to rescan the target, in order to
+ detect the case when an entire target has appeared or
+ disappeared. These two events will never be reported unless the
+ VIRTIO_SCSI_F_HOTPLUG feature was negotiated between the host
+ and the guest.
+
+ Events will also be reported via sense codes (this obviously
+ does not apply to newly appeared buses or targets, since the
+ application has never discovered them):
+
+ • “LUN/target removed” maps to sense key ILLEGAL REQUEST, asc
+ 0x25, ascq 0x00 (LOGICAL UNIT NOT SUPPORTED)
+
+ • “LUN hard reset” maps to sense key UNIT ATTENTION, asc 0x29
+ (POWER ON, RESET OR BUS DEVICE RESET OCCURRED)
+
+ • “rescan LUN/target” maps to sense key UNIT ATTENTION, asc
+ 0x3f, ascq 0x0e (REPORTED LUNS DATA HAS CHANGED)
+
+ The preferred way to detect transport reset is always to use
+ events, because sense codes are only seen by the driver when it
+ sends a SCSI command to the logical unit or target. However, in
+ case events are dropped, the initiator will still be able to
+ synchronize with the actual state of the controller if the
+ driver asks the initiator to rescan of the SCSI bus. During the
+ rescan, the initiator will be able to observe the above sense
+ codes, and it will process them as if it the driver had
+ received the equivalent event.
+
+ Asynchronous notification
+ #define VIRTIO_SCSI_T_ASYNC_NOTIFY 2
+
+ struct virtio_scsi_event_an {
+ // Write-only part
+ u32 event;
+ u8 lun[8];
+ u32 reason;
+ }
+
+ By sending this event, the device signals that an asynchronous
+ event was fired from a physical interface.
+
+ All fields are written by the device. The event field is set to
+ VIRTIO_SCSI_T_ASYNC_NOTIFY. The lun field addresses a logical
+ unit in the SCSI host. The reason field is a subset of the
+ events that the driver has subscribed to via the "Asynchronous
+ notification subscription" command.
+
+ When dropped events are reported, the driver should poll for
+ asynchronous events manually using SCSI commands.
+
+Appendix X: virtio-mmio
+
+Virtual environments without PCI support (a common situation in
+embedded devices models) might use simple memory mapped device (“
+virtio-mmio”) instead of the PCI device.
+
+The memory mapped virtio device behaviour is based on the PCI
+device specification. Therefore most of operations like device
+initialization, queues configuration and buffer transfers are
+nearly identical. Existing differences are described in the
+following sections.
+
+Device Initialization
+
+Instead of using the PCI IO space for virtio header, the “
+virtio-mmio” device provides a set of memory mapped control
+registers, all 32 bits wide, followed by device-specific
+configuration space. The following list presents their layout:
+
+• Offset from the device base address | Direction | Name
+ Description
+
+• 0x000 | R | MagicValue
+ “virt” string.
+
+• 0x004 | R | Version
+ Device version number. Currently must be 1.
+
+• 0x008 | R | DeviceID
+ Virtio Subsystem Device ID (ie. 1 for network card).
+
+• 0x00c | R | VendorID
+ Virtio Subsystem Vendor ID.
+
+• 0x010 | R | HostFeatures
+ Flags representing features the device supports.
+ Reading from this register returns 32 consecutive flag bits,
+ first bit depending on the last value written to
+ HostFeaturesSel register. Access to this register returns bits HostFeaturesSel*32
+
+ to (HostFeaturesSel*32)+31, eg. feature bits 0 to 31 if
+ HostFeaturesSel is set to 0 and features bits 32 to 63 if
+ HostFeaturesSel is set to 1. Also see [sub:Feature-Bits]
+
+• 0x014 | W | HostFeaturesSel
+ Device (Host) features word selection.
+ Writing to this register selects a set of 32 device feature bits
+ accessible by reading from HostFeatures register. Device driver
+ must write a value to the HostFeaturesSel register before
+ reading from the HostFeatures register.
+
+• 0x020 | W | GuestFeatures
+ Flags representing device features understood and activated by
+ the driver.
+ Writing to this register sets 32 consecutive flag bits, first
+ bit depending on the last value written to GuestFeaturesSel
+ register. Access to this register sets bits GuestFeaturesSel*32
+ to (GuestFeaturesSel*32)+31, eg. feature bits 0 to 31 if
+ GuestFeaturesSel is set to 0 and features bits 32 to 63 if
+ GuestFeaturesSel is set to 1. Also see [sub:Feature-Bits]
+
+• 0x024 | W | GuestFeaturesSel
+ Activated (Guest) features word selection.
+ Writing to this register selects a set of 32 activated feature
+ bits accessible by writing to the GuestFeatures register.
+ Device driver must write a value to the GuestFeaturesSel
+ register before writing to the GuestFeatures register.
+
+• 0x028 | W | GuestPageSize
+ Guest page size.
+ Device driver must write the guest page size in bytes to the
+ register during initialization, before any queues are used.
+ This value must be a power of 2 and is used by the Host to
+ calculate Guest address of the first queue page (see QueuePFN).
+
+• 0x030 | W | QueueSel
+ Virtual queue index (first queue is 0).
+ Writing to this register selects the virtual queue that the
+ following operations on QueueNum, QueueAlign and QueuePFN apply
+ to.
+
+• 0x034 | R | QueueNumMax
+ Maximum virtual queue size.
+ Reading from the register returns the maximum size of the queue
+ the Host is ready to process or zero (0x0) if the queue is not
+ available. This applies to the queue selected by writing to
+ QueueSel and is allowed only when QueuePFN is set to zero
+ (0x0), so when the queue is not actively used.
+
+• 0x038 | W | QueueNum
+ Virtual queue size.
+ Queue size is a number of elements in the queue, therefore size
+ of the descriptor table and both available and used rings.
+ Writing to this register notifies the Host what size of the
+ queue the Guest will use. This applies to the queue selected by
+ writing to QueueSel.
+
+• 0x03c | W | QueueAlign
+ Used Ring alignment in the virtual queue.
+ Writing to this register notifies the Host about alignment
+ boundary of the Used Ring in bytes. This value must be a power
+ of 2 and applies to the queue selected by writing to QueueSel.
+
+• 0x040 | RW | QueuePFN
+ Guest physical page number of the virtual queue.
+ Writing to this register notifies the host about location of the
+ virtual queue in the Guest's physical address space. This value
+ is the index number of a page starting with the queue
+ Descriptor Table. Value zero (0x0) means physical address zero
+ (0x00000000) and is illegal. When the Guest stops using the
+ queue it must write zero (0x0) to this register.
+ Reading from this register returns the currently used page
+ number of the queue, therefore a value other than zero (0x0)
+ means that the queue is in use.
+ Both read and write accesses apply to the queue selected by
+ writing to QueueSel.
+
+• 0x050 | W | QueueNotify
+ Queue notifier.
+ Writing a queue index to this register notifies the Host that
+ there are new buffers to process in the queue.
+
+• 0x60 | R | InterruptStatus
+Interrupt status.
+Reading from this register returns a bit mask of interrupts
+ asserted by the device. An interrupt is asserted if the
+ corresponding bit is set, ie. equals one (1).
+
+ – Bit 0 | Used Ring Update
+ This interrupt is asserted when the Host has updated the Used
+ Ring in at least one of the active virtual queues.
+
+ – Bit 1 | Configuration change
+ This interrupt is asserted when configuration of the device has
+ changed.
+
+• 0x064 | W | InterruptACK
+ Interrupt acknowledge.
+ Writing to this register notifies the Host that the Guest
+ finished handling interrupts. Set bits in the value clear the
+ corresponding bits of the InterruptStatus register.
+
+• 0x070 | RW | Status
+ Device status.
+ Reading from this register returns the current device status
+ flags.
+ Writing non-zero values to this register sets the status flags,
+ indicating the Guest progress. Writing zero (0x0) to this
+ register triggers a device reset.
+ Also see [sub:Device-Initialization-Sequence]
+
+• 0x100+ | RW | Config
+ Device-specific configuration space starts at an offset 0x100
+ and is accessed with byte alignment. Its meaning and size
+ depends on the device and the driver.
+
+Virtual queue size is a number of elements in the queue,
+therefore size of the descriptor table and both available and
+used rings.
+
+The endianness of the registers follows the native endianness of
+the Guest. Writing to registers described as “R” and reading from
+registers described as “W” is not permitted and can cause
+undefined behavior.
+
+The device initialization is performed as described in 2.2.1 Device
+Initialization Sequence with one exception: the Guest must notify the
+Host about its page size, writing the size in bytes to GuestPageSize
+register before the initialization is finished.
+
+The memory mapped virtio devices generate single interrupt only,
+therefore no special configuration is required.
+
+Virtqueue Configuration
+
+The virtual queue configuration is performed in a similar way to
+the one described in 2.3 Virtqueue Configuration with a few
+additional operations:
+
+1. Select the queue writing its index (first queue is 0) to the
+ QueueSel register.
+
+2. Check if the queue is not already in use: read QueuePFN
+ register, returned value should be zero (0x0).
+
+3. Read maximum queue size (number of elements) from the
+ QueueNumMax register. If the returned value is zero (0x0) the
+ queue is not available.
+
+4. Allocate and zero the queue pages in contiguous virtual
+ memory, aligning the Used Ring to an optimal boundary (usually
+ page size). Size of the allocated queue may be smaller than or
+ equal to the maximum size returned by the Host.
+
+5. Notify the Host about the queue size by writing the size to
+ QueueNum register.
+
+6. Notify the Host about the used alignment by writing its value
+ in bytes to QueueAlign register.
+
+7. Write the physical number of the first page of the queue to
+ the QueuePFN register.
+
+The queue and the device are ready to begin normal operations
+now.
+
+Device Operation
+
+The memory mapped virtio device behaves in the same way as
+described in 2.4 Device Operation, with the following
+exceptions:
+
+1. The device is notified about new buffers available in a queue
+ by writing the queue index to register QueueNum instead of the
+ virtio header in PCI I/O space (2.4.1.4 Notifying The Device).
+
+2. The memory mapped virtio device is using single, dedicated
+ interrupt signal, which is raised when at least one of the
+ interrupts described in the InterruptStatus register
+ description is asserted. After receiving an interrupt, the
+ driver must read the InterruptStatus register to check what
+ caused the interrupt (see the register description). After the
+ interrupt is handled, the driver must acknowledge it by writing
+ a bit mask corresponding to the serviced interrupt to the
+ InterruptACK register.
+
+
+FOOTNOTES:
+[1] This lack of page-sharing implies that the implementation of the
+device (e.g. the hypervisor or host) needs full access to the
+guest memory. Communication with untrusted parties (i.e.
+inter-guest communication) requires copying.
+
+[2] The Linux implementation further separates the PCI virtio code
+from the specific virtio drivers: these drivers are shared with
+the non-PCI implementations (currently lguest and S/390).
+
+[3] The actual value within this range is ignored
+
+[4] Historically, drivers have used the device before steps 5 and 6.
+This is only allowed if the driver does not use any features
+which would alter this early use of the device.
+
+[5] ie. once you enable MSI-X on the device, the other fields move.
+If you turn it off again, they move back!
+
+[6] The 4096 is based on the x86 page size, but it's also large
+enough to ensure that the separate parts of the virtqueue are on
+separate cache lines.
+
+[7] These fields are kept here because this is the only part of the
+virtqueue written by the device
+
+[8] The Linux drivers do this only for read-only buffers: for
+write-only buffers, it is assumed that the driver is merely
+trying to keep the receive buffer ring full, and no notification
+of this expected condition is necessary.
+
+[9] https://lists.linux-foundation.org/mailman/listinfo/virtualization
+
+[10] The current qemu device implementations mistakenly insist that
+the first descriptor cover the header in these cases exactly, so
+a cautious driver should arrange it so.
+
+[11] Even if it does mean documenting design or implementation
+mistakes!
+
+[12] Only if VIRTIO_NET_F_CTRL_VQ set
+
+[13] It was supposed to indicate segmentation offload support, but
+upon further investigation it became clear that multiple bits
+were required.
+
+[14] ie. VIRTIO_NET_F_HOST_TSO* and VIRTIO_NET_F_HOST_UFO are
+dependent on VIRTIO_NET_F_CSUM; a dvice which offers the offload
+features must offer the checksum feature, and a driver which
+accepts the offload features must accept the checksum feature.
+Similar logic applies to the VIRTIO_NET_F_GUEST_TSO4 features
+depending on VIRTIO_NET_F_GUEST_CSUM.
+
+[15] This is a common restriction in real, older network cards.
+
+[16] For example, a network packet transported between two guests on
+the same system may not require checksumming at all, nor segmentation,
+if both guests are amenable.
+
+[17] For example, consider a partially checksummed TCP (IPv4) packet.
+It will have a 14 byte ethernet header and 20 byte IP header
+followed by the TCP header (with the TCP checksum field 16 bytes
+into that header). csum_start will be 14+20 = 34 (the TCP
+checksum includes the header), and csum_offset will be 16. The
+value in the TCP checksum field should be initialized to the sum
+of the TCP pseudo header, so that replacing it by the ones'
+complement checksum of the TCP header and body will give the
+correct result.
+
+[18] Due to various bugs in implementations, this field is not useful
+as a guarantee of the transport header size.
+
+[19] This case is not handled by some older hardware, so is called out
+specifically in the protocol.
+
+[20] Note that the header will be two bytes longer for the
+VIRTIO_NET_F_MRG_RXBUF case.
+
+[20a] Obviously each one can be split across multiple descriptor
+elements.
+
+[21] Since there are no guarentees, it can use a hash filter or
+silently switch to allmulti or promiscuous mode if it is given too
+many addresses.
+
+[22] The SCSI_CMD and SCSI_CMD_OUT types are equivalent, the device
+does not distinguish between them.
+
+[23] The FLUSH and FLUSH_OUT types are equivalent, the device does not
+distinguish between them
+
+[24] Ports 2 onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set.
+
+[25] Because this is high importance and low bandwidth, the current
+Linux implementation polls for the buffer to be used, rather than
+waiting for an interrupt, simplifying the implementation
+significantly. However, for generic serial ports with the
+O_NONBLOCK flag set, the polling limitation is relaxed and the
+consumed buffers are freed upon the next write or poll call or
+when a port is closed or hot-unplugged.
+
+[26] Only if VIRTIO_BALLON_F_STATS_VQ set.
+
+[27] This is historical, and independent of the guest page size
+
+[28] In this case, deflation advice is merely a courtesy
+
+[29] As updates to configuration space are not atomic, this field
+isn't particularly reliable, but can be used to diagnose buggy guests.