| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This resolves the panic on FreeBSD during VT switch, without attempting
any of the more lofty goals for the time being.
|
|
Conflicts:
shared-core/i915_dma.c
This brings in kernel support and userland interface for intel GEM.
|
|
This reverts commit 965a72202b439068e62ac341990f51953457b202.
Please re-do over properly
|
|
|
|
Conflicts:
linux-core/Makefile.kernel
shared-core/i915_dma.c
shared-core/i915_drv.h
shared-core/i915_irq.c
|
|
This resolves a panic on FreeBSD which was caused by trying
to re-initialize the swap lock. It's just much easier to
initialize all of the locks at load time. It should also
ensure that the vblank structures are available earlier.
|
|
All interrupt off vblank count updates are done in drm_vblank_get/put
now, so convert users of the vblank counter over to that interface.
|
|
Remove the unused (and broken) "in vblank" code now that the core has
been fixed to use a counter while interrupts are enabled. Also make the
vblank pipe get/set ioctls into dumb stub functions, since with the new
code we can no longer let userspace control whether vblank interrupts
are enabled, or the core code will misbehave.
|
|
modifications to make it work correctly on my test hardware (altered the
backlight write function, made it enable the legacy backlight controller
interrupts on mobile hardware, sorted the interrupt function so we don't
get an excessive number of vblank interrupts). This lets the backlight
keys on my T61 work properly, though there's a 750msec or so delay
between the request and the brightness actually changing - this sounds
awfully like the hardware spinning waiting for a status flag to become
ready, but as far as I can tell they're all set correctly. If anyone can
figure out what's wrong here, it'd be nice to know.
Some of the functions are still stubs and just tell the hardware that
the request was successful. These can be filled in as kernel modesetting
gets integrated. I think it's worth getting this in anyway, since it's
required for backlight control to work properly on some new platforms.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
When scheduled swaps occur, we need to blit between front & back buffers. I
the buffers are tiled, we need to set the appropriate XY_SRC_COPY tile bit,
only on 965 chips, since it will cause corruption on pre-965 (e.g. 945).
Bug reported by and fix tested by Tomas Janousek <tomi@nomi.cz>.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
With the interrupt enable/disable using only the mask register, it was wrong
to use the enable register to detect which pipes had vblank detection
turned on. Also, as we keep a local copy of the mask register around, and
MSI machines smack the hardware during the interrupt handler, it is more
efficient and more correct to use the local copy.
|
|
This shares common code sequences for managing the interrupt register bits
|
|
It would be nice if one day the DRM driver was the canonical source for
register definitions and core macros. To that end, this patch cleans things up
quite a bit, removing redundant definitions (some with different names
referring to the same register) and generally tidying up the header file.
|
|
Noting that the interrupt mask register was more reliable than the interrupt
enable register for managing interrupts in user_irq_on/user_irq_off, this
patch replaces the remaining IER frobbing with IMR instead.
The test which exposes IER related failures is:
$ glxgears & glxgears & glxgears
(reposition the glxgears windows away from the upper left corner)
$ while :; do x11perf -rect100 -reps 800 -repeat 1; sleep 1; done &
$ while :; do runoa; runet; done &
|
|
Another patch adds this to a /proc/dri file for debugging and monitoring.
|
|
This adds gem_active, gem_flushing, gem_inactive, gem_request and gem_seqno
entries to monitor gem operation and help debug issues.
|
|
|
|
The interrupt identity register must be writen before any work occurs lest
we drop an interrupt on the floor. This patch just shuffles code around to
make sure that IIR is written as early as possible.
|
|
In the short-circuit code for the breadcrumb already being new enough, we
need to update the sarea_priv copy of the breadcrumb just as if we had
waited. Otherwise userland error checking will notice that we returned
too early based on its wrong information, and call wait_irq again (leading
to spinning until someone else comes along and updates the sarea_priv).
This bug was hidden when we had interrupt masking disabled, such as in
master, since the interrupt handler would update sarea_priv.
|
|
This was insufficient once we started masking interrupts to only when someone
was waiting for them (and would thus retire requests themselves). It was
replaced by the retire_timer.
|
|
This fixes a regression from commit d434b64f6a760d85295e32298a9a1f3624ee1b69
which could cause us to fail to wake up for user interrupts if we lost a race.
|
|
|
|
This requires that the X Server use the execbuf interface for buffer
submission, as it no longer has direct access to the ring. This is
therefore a flag day for the gem interface.
This also adds enter/leavevt ioctls for use by the X Server. These would
get stubbed out in a modesetting implementation, but are required while
in an environment where the device's state is only managed by the DRM while
X has the VT.
|
|
Conflicts:
linux-core/Makefile.kernel
shared-core/i915_drv.h
shared-core/nouveau_state.c
|
|
The i915 driver now works again.
|
|
The interrupt enable register cannot be used to temporarily disable
interrupts, instead use the interrupt mask register.
Note that this change means that a pile of buffers will be left stuck on the
chip as the final interrupts will not be recognized to come and drain things.
|
|
There are now 3 lists. Active is buffers currently in the ringbuffer.
Flushing is not in the ringbuffer, but needs a flush before unbinding.
Inactive is as before. This prevents object_free → unbind →
wait_rendering → object_reference and a kernel oops about weird refcounting.
This also avoids an synchronous extra flush and wait when freeing a buffer
which had a write_domain set (such as a temporary rendered to and then from
using the 2d engine). It will sit around on the flushing list until the
appropriate flush gets emitted, or we need the GTT space for another
operation.
|
|
|
|
The vblank tasklet update code must build 2D blt commands with the
appropriate tiled flags.
|
|
The batchbuffer submission paths were fixed to use the 965-specific command,
but the vblank tasklet was not. When the older version is sent, the 965 will
lock up.
|
|
My 965GM gets interrupts stuck when using the old PIPE_VBLANK interrupt.
Switch to the PIPE_EVENT interrupt mechanism, and set the PIPE*STAT
registers to use START_VBLANK on 965 and VBLANK on previous chips.
|
|
to leap it's vblank count a huge value.
This will stall some applications that switch video mode if vblank_mode is set to a non zero value in drirc.
|
|
|
|
We need to return an accurate vblank count to the callers of
->get_vblank_counter, and in the Intel case the actual frame count
register isn't udpated until the next active line is displayed, so we
need to return one more than the frame count register if we're currently
in a vblank period.
However, none of the various ways of doing this is working yet, so
disable the logic for now. This may result in a few missed events, but
should fix the hangs some people have seen due to the current code
tripping the wraparound logic in drm_update_vblank_count.
|
|
Should use vtotal not htotal to figure out if we're in a vblank period.
|
|
The frame count registers don't increment until the start of the next
frame, so make sure we return an incremented count if called during the
actual vblank period.
|
|
Ack the IRQs correctly (PIPExSTAT first followed by IIR). Don't read
vblank counter registers on disabled pipes (might hang otherwise). And
deal with flipped pipe/plane mappings if present.
|
|
Conflicts:
linux-core/drmP.h
linux-core/drm_drv.c
shared-core/i915_drv.h
shared-core/i915_irq.c
shared-core/mga_irq.c
shared-core/radeon_irq.c
shared-core/via_irq.c
Mostly trivial conflicts.
mach64 support from Mathieu Bérard.
|
|
This reverts commit bfc29606e4a818897eebca46a5e23bbe7bc3ce25.
This regresses i915 here for me I can't get greater than 0.333 fps with gears
|
|
As DRM_DEBUG macro already prints out the __FUNCTION__ string (see
drivers/char/drm/drmP.h), it is not worth doing this again. At some
other places the ending "\n" was added.
airlied:- I cleaned up a few that this patch missed also
|
|
The casting is safe only when the list_head member is the first member of
the structure.
|
|
If drmMinor >= 6, the intel DDX driver will enable vblank events on both
pipes. If drmMinor >= 10 on pre-965 chipsets, the intel DDX driver will
swap the pipe<->plane mapping to allow for framebuffer compression on
laptop screens. This means the secondary vblank counter (corresponding
to pipe B) will be incremented when vblank interrupts occur.
Now Mesa waits for vblank events on whichever plane has a greater
portion of the displayed window. So it will happly ask to wait for the
primary counter even though that one won't increment.
So we can fix this in either the DDX driver, Mesa or the kernel (though
I thought we already had several times).
Since current (and previous) userspace assumes it's talking about a pipe
== plane situation and now uses planes when talking to the kernel, we
should probably just hide the mapping details there (indeed they already
are hidden there for vblank swaps), which this patch does.
So as far as userland is concerned, whether we call things planes or
pipes is irrelevant, as long as kernel developers understand that
userland hands them planes and they have to figure out which pipe that
corresponds to (which will typically be the same on 965+ hardware and
reversed on pre-965 mobile chips).
|
|
This field isn't touched or read by any other code in the stack so it's
time to retire these last few references.
|
|
|
|
Kernel "cleanfile" script run.
|
|
Conflicts:
linux-core/drmP.h
linux-core/drm_drv.c
linux-core/drm_irq.c
shared-core/i915_drv.h
shared-core/i915_irq.c
shared-core/mga_drv.h
shared-core/mga_irq.c
shared-core/radeon_drv.h
shared-core/radeon_irq.c
Merge in the latest master bits and update the remaining drivers (except
mach64 which math_b is working on). Also remove the 9xx hack from the i915
driver; it seems to be correct.
|
|
|
|
|
|
One instance of unlocking a spinlock was converted incorrectly when this code
was fixed to build on BSD.
|
