From 8038e7b60f62e51b7f134141fd58f334eec31a10 Mon Sep 17 00:00:00 2001 From: Oliver McFadden Date: Mon, 18 Jun 2007 08:36:50 +0000 Subject: r300: Synchronized the register defines file again. --- shared-core/r300_reg.h | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-) (limited to 'shared-core/r300_reg.h') diff --git a/shared-core/r300_reg.h b/shared-core/r300_reg.h index 0a31f0b9..3ce09c16 100644 --- a/shared-core/r300_reg.h +++ b/shared-core/r300_reg.h @@ -116,6 +116,8 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. # define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */ #define R300_VAP_OUTPUT_VTX_FMT_1 0x2094 + /* each of the following is 3 bits wide, specifies number + of components */ # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6 @@ -299,6 +301,18 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. # define R300_221C_NORMAL 0x00000000 # define R300_221C_CLEAR 0x0001C000 +/* These seem to be per-pixel and per-vertex X and Y clipping planes. The first + * plane is per-pixel and the second plane is per-vertex. + * + * This was determined by experimentation alone but I believe it is correct. + * + * These registers are called X_QUAD0_1_FL to X_QUAD0_4_FL by glxtest. + */ +#define R300_VAP_CLIP_X_0 0x2220 +#define R300_VAP_CLIP_X_1 0x2224 +#define R300_VAP_CLIP_Y_0 0x2228 +#define R300_VAP_CLIP_Y_1 0x2230 + /* gap */ /* Sometimes, END_OF_PKT and 0x2284=0 are the only commands sent between @@ -967,7 +981,6 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. * first node is stored in NODE_2, the second node is stored in NODE_3. * * Offsets are relative to the master offset from PFS_CNTL_2. - * LAST_NODE is set for the last node, and only for the last node. */ #define R300_PFS_NODE_0 0x4610 #define R300_PFS_NODE_1 0x4614 @@ -981,7 +994,6 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. # define R300_PFS_NODE_TEX_OFFSET_MASK (31 << 12) # define R300_PFS_NODE_TEX_END_SHIFT 17 # define R300_PFS_NODE_TEX_END_MASK (31 << 17) -/*# define R300_PFS_NODE_LAST_NODE (1 << 22) */ # define R300_PFS_NODE_OUTPUT_COLOR (1 << 22) # define R300_PFS_NODE_OUTPUT_DEPTH (1 << 23) @@ -1591,6 +1603,7 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. # define R300_EB_UNK1_SHIFT 24 # define R300_EB_UNK1 (0x80<<24) # define R300_EB_UNK2 0x0810 +#define R300_PACKET3_3D_DRAW_VBUF_2 0x00003400 #define R300_PACKET3_3D_DRAW_INDX_2 0x00003600 /* END: Packet 3 commands */ -- cgit v1.2.3 From 40f6a696cb22ffa064f78198a7a241015d365967 Mon Sep 17 00:00:00 2001 From: Oliver McFadden Date: Thu, 21 Jun 2007 14:35:11 +0000 Subject: r300: Synchronized the register defines file; documentation changes. --- shared-core/r300_reg.h | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'shared-core/r300_reg.h') diff --git a/shared-core/r300_reg.h b/shared-core/r300_reg.h index 3ce09c16..e59919be 100644 --- a/shared-core/r300_reg.h +++ b/shared-core/r300_reg.h @@ -336,13 +336,15 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. * The meaning of the two UNKNOWN fields is obviously not known. However, * experiments so far have shown that both *must* point to an instruction * inside the vertex program, otherwise the GPU locks up. + * * fglrx usually sets CNTL_3_UNKNOWN to the end of the program and - * CNTL_1_UNKNOWN points to instruction where last write to position takes - * place. + * R300_PVS_CNTL_1_POS_END_SHIFT points to instruction where last write to + * position takes place. + * * Most likely this is used to ignore rest of the program in cases * where group of verts arent visible. For some reason this "section" * is sometimes accepted other instruction that have no relationship with - *position calculations. + * position calculations. */ #define R300_VAP_PVS_CNTL_1 0x22D0 # define R300_PVS_CNTL_1_PROGRAM_START_SHIFT 0 -- cgit v1.2.3