Age | Commit message (Collapse) | Author |
|
This fixes registration when MSI is set up after the stub function fills in
dev->irq. Otherwise /proc/interrupts would report attachment to the fasteoi
interrupt. dev->irq is still exposed (and updated at IRQ setup)
for the drivers that use it for whatever reason.
|
|
|
|
|
|
|
|
Record the last execbuffer sequence for each client.
Record that sequence in the throttle ioctl as the 'throttle sequence'.
Wait for the last throttle sequence in the throttle ioctl.
|
|
|
|
The interrupt identity register must be writen before any work occurs lest
we drop an interrupt on the floor. This patch just shuffles code around to
make sure that IIR is written as early as possible.
|
|
We want request retirement to occur about once a second when the request
queue is non-empty. This was done with a timer that queued a work_struct,
using a delayed_work instead makes a lot more sense.
|
|
In the short-circuit code for the breadcrumb already being new enough, we
need to update the sarea_priv copy of the breadcrumb just as if we had
waited. Otherwise userland error checking will notice that we returned
too early based on its wrong information, and call wait_irq again (leading
to spinning until someone else comes along and updates the sarea_priv).
This bug was hidden when we had interrupt masking disabled, such as in
master, since the interrupt handler would update sarea_priv.
|
|
This was insufficient once we started masking interrupts to only when someone
was waiting for them (and would thus retire requests themselves). It was
replaced by the retire_timer.
|
|
|
|
This patch should fixe hard lockup and convert them in
softlockup (ie you can ssh the box but the gpu is busted
and we are waiting in loop for it to come back to reason).
|
|
This fixes a regression from commit d434b64f6a760d85295e32298a9a1f3624ee1b69
which could cause us to fail to wake up for user interrupts if we lost a race.
|
|
Use GEM for ring buffer setup and framebuffer allocation. This means reworking
the hardware status page stuff a bit (just use the basic range allocator for
vram for now) and #ifdef'ing out the TTM & DRI2 code. Works well enough to
load/unload several times and display fbcon on my T61 (though there's still
some unexplained console corruption).
|
|
|
|
According to the hw guys, you should use DSTCACHE_CTLSTAT to flush
the 2D dst cache rather than RB2D_DSTCACHE_CTLSTAT.
|
|
This is the create (may want location flags), pread/pwrite/mmap
(performance tuning hints), and set_domain (will 32 bits be enough for
everyone?) ioctls. Left in the generic set are just flink/open/close.
The 2D driver must be updated for this change, and API but not ABI is broken
for 3D. The driver version is bumped to mark this.
|
|
Use new GEM based ring buffer initialization. Still need to init GEM & use it
for framebuffer allocation etc.
Conflicts:
shared-core/i915_dma.c
shared-core/i915_drv.h
|
|
|
|
This requires that the X Server use the execbuf interface for buffer
submission, as it no longer has direct access to the ring. This is
therefore a flag day for the gem interface.
This also adds enter/leavevt ioctls for use by the X Server. These would
get stubbed out in a modesetting implementation, but are required while
in an environment where the device's state is only managed by the DRM while
X has the VT.
|
|
|
|
Passed the compile test; it's ready to ship.
Conflicts:
libdrm/Makefile.am
linux-core/Makefile.kernel
linux-core/drmP.h
linux-core/drm_memrange.c
linux-core/drm_stub.c
shared-core/drm.h
shared-core/i915_dma.c
shared-core/i915_drv.h
shared-core/i915_irq.c
|
|
GART setup appears to work the same as RS480 chips.
Also RC4xx chips are actually RS400 based, not RS480 based.
|
|
|
|
Reported by vehemens
|
|
|
|
|
|
The driver can know what hardware requires MI_BATCH_BUFFER vs
MI_BATCH_BUFFER_START; there's no reason to let user mode configure this.
|
|
The driver can know what hardware requires MI_BATCH_BUFFER vs
MI_BATCH_BUFFER_START; there's no reason to let user mode configure this.
|
|
Without the user IRQ running constantly, there's no wakeup when the ring
empties to go retire requests and free buffers. Use a 1 second timer to make
that happen more often.
|
|
This goes with the other hardware status page patch.
|
|
Instead of throttling and execbuffer time, have the application ask to
throttle explicitly. This allows the throttle to happen less often, and
without holding the DRM lock.
|
|
I couldn't get the re-allocated HWS to work on my 965GM, so I just gave up
and made it persist across the lifetime of the driver instead.
|
|
|
|
|
|
Fixes performance drop after suspend/resume on some systems.
|
|
|
|
Idea being if you want to add new crtc/output/encoder dynamically later,
you just increase the generation counter and userspace should re-read
all the resources
|
|
|
|
|
|
Move dpms into the helper functions.
Move crtc into the encoder.
Move disable unused functions into the helper.
|
|
|
|
Conflicts:
linux-core/Makefile.kernel
shared-core/i915_drv.h
shared-core/nouveau_state.c
|
|
|
|
|
|
Okay we have crtc, encoder and connectors.
No more outputs exposed beyond driver internals
I've broken intel tv connector stuff.
Really for TV we should have one TV connector, with a sub property for the
type of signal been driven over it
|
|
Time to do some renaming on the connectors I think
|
|
|
|
Use subclassing from the drivers to allocate the objects. This saves
two objects being allocated for each crtc/output and generally makes
exit paths cleaner.
|
|
This splits a lot of the core modesetting code out into a file of
helper functions, that are only called from themselves and/or the driver.
The driver gets called into more often or can call these functions from itself
if it is a helper using driver.
I've broken framebuffer resize doing this but I didn't like the API for that
in any case.
|