summaryrefslogtreecommitdiff
path: root/shared-core
diff options
context:
space:
mode:
Diffstat (limited to 'shared-core')
-rw-r--r--shared-core/r300_reg.h1001
1 files changed, 577 insertions, 424 deletions
diff --git a/shared-core/r300_reg.h b/shared-core/r300_reg.h
index 0717e731..69bc994c 100644
--- a/shared-core/r300_reg.h
+++ b/shared-core/r300_reg.h
@@ -48,12 +48,12 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
# define R300_MC_MISC__MC_GLOBW_FULL_LAT_SHIFT 28
/*
-This file contains registers and constants for the R300. They have been
-found mostly by examining command buffers captured using glxtest, as well
-as by extrapolating some known registers and constants from the R200.
-
-I am fairly certain that they are correct unless stated otherwise in comments.
-*/
+ * This file contains registers and constants for the R300. They have been
+ * found mostly by examining command buffers captured using glxtest, as well
+ * as by extrapolating some known registers and constants from the R200.
+ * I am fairly certain that they are correct unless stated otherwise
+ * in comments.
+ */
#define R300_SE_VPORT_XSCALE 0x1D98
#define R300_SE_VPORT_XOFFSET 0x1D9C
@@ -63,46 +63,54 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_SE_VPORT_ZOFFSET 0x1DAC
-/* This register is written directly and also starts data section in many 3d CP_PACKET3's */
-#define R300_VAP_VF_CNTL 0x2084
+/*
+ * Vertex Array Processing (VAP) Control
+ * Stolen from r200 code from Christoph Brill (It's a guess!)
+ */
+#define R300_VAP_CNTL 0x2080
-# define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0
-# define R300_VAP_VF_CNTL__PRIM_NONE (0<<0)
-# define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0)
-# define R300_VAP_VF_CNTL__PRIM_LINES (2<<0)
-# define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0)
-# define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0)
-# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0)
-# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0)
-# define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0)
-# define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0)
-# define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0)
-# define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0)
-
-# define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4
- /* State based - direct writes to registers trigger vertex generation */
-# define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4)
-# define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4)
-# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4)
-# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4)
-
- /* I don't think I saw these three used.. */
-# define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6
-# define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9
-# define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10
-
- /* index size - when not set the indices are assumed to be 16 bit */
-# define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11)
- /* number of vertices */
-# define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16
+/* This register is written directly and also starts data section
+ * in many 3d CP_PACKET3's
+ */
+#define R300_VAP_VF_CNTL 0x2084
+# define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0
+# define R300_VAP_VF_CNTL__PRIM_NONE (0<<0)
+# define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0)
+# define R300_VAP_VF_CNTL__PRIM_LINES (2<<0)
+# define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0)
+# define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0)
+# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0)
+# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0)
+# define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0)
+# define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0)
+# define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0)
+# define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0)
+
+# define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4
+ /* State based - direct writes to registers trigger vertex
+ generation */
+# define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4)
+# define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4)
+# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4)
+# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4)
+
+ /* I don't think I saw these three used.. */
+# define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6
+# define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9
+# define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10
+
+ /* index size - when not set the indices are assumed to be 16 bit */
+# define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11)
+ /* number of vertices */
+# define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16
/* BEGIN: Wild guesses */
#define R300_VAP_OUTPUT_VTX_FMT_0 0x2090
# define R300_VAP_OUTPUT_VTX_FMT_0__POS_PRESENT (1<<0)
# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_PRESENT (1<<1)
-# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */
-# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */
-# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */
+# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */
+# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */
+# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */
# define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */
#define R300_VAP_OUTPUT_VTX_FMT_1 0x2094
@@ -114,7 +122,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15
# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18
# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21
-/* END */
+/* END: Wild guesses */
#define R300_SE_VTE_CNTL 0x20b0
# define R300_VPORT_X_SCALE_ENA 0x00000001
@@ -130,29 +138,39 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_VTX_ST_DENORMALIZED 0x00001000
/* BEGIN: Vertex data assembly - lots of uncertainties */
+
+/* gap */
+
+#define R300_VAP_CNTL_STATUS 0x2140
+# define R300_VC_NO_SWAP (0 << 0)
+# define R300_VC_16BIT_SWAP (1 << 0)
+# define R300_VC_32BIT_SWAP (2 << 0)
+
/* gap */
+
/* Where do we get our vertex data?
-//
-// Vertex data either comes either from immediate mode registers or from
-// vertex arrays.
-// There appears to be no mixed mode (though we can force the pitch of
-// vertex arrays to 0, effectively reusing the same element over and over
-// again).
-//
-// Immediate mode is controlled by the INPUT_CNTL registers. I am not sure
-// if these registers influence vertex array processing.
-//
-// Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3.
-//
-// In both cases, vertex attributes are then passed through INPUT_ROUTE.
-
-// Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data
-// into the vertex processor's input registers.
-// The first word routes the first input, the second word the second, etc.
-// The corresponding input is routed into the register with the given index.
-// The list is ended by a word with INPUT_ROUTE_END set.
-//
-// Always set COMPONENTS_4 in immediate mode. */
+ *
+ * Vertex data either comes either from immediate mode registers or from
+ * vertex arrays.
+ * There appears to be no mixed mode (though we can force the pitch of
+ * vertex arrays to 0, effectively reusing the same element over and over
+ * again).
+ *
+ * Immediate mode is controlled by the INPUT_CNTL registers. I am not sure
+ * if these registers influence vertex array processing.
+ *
+ * Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3.
+ *
+ * In both cases, vertex attributes are then passed through INPUT_ROUTE.
+ *
+ * Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data
+ * into the vertex processor's input registers.
+ * The first word routes the first input, the second word the second, etc.
+ * The corresponding input is routed into the register with the given index.
+ * The list is ended by a word with INPUT_ROUTE_END set.
+ *
+ * Always set COMPONENTS_4 in immediate mode.
+ */
#define R300_VAP_INPUT_ROUTE_0_0 0x2150
# define R300_INPUT_ROUTE_COMPONENTS_1 (0 << 0)
@@ -176,10 +194,12 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_VAP_INPUT_ROUTE_0_7 0x216C
/* gap */
+
/* Notes:
-// - always set up to produce at least two attributes:
-// if vertex program uses only position, fglrx will set normal, too
-// - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal */
+ * - always set up to produce at least two attributes:
+ * if vertex program uses only position, fglrx will set normal, too
+ * - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal.
+ */
#define R300_VAP_INPUT_CNTL_0 0x2180
# define R300_INPUT_CNTL_0_COLOR 0x00000001
#define R300_VAP_INPUT_CNTL_1 0x2184
@@ -196,12 +216,14 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_INPUT_CNTL_TC7 0x00020000 /* GUESS */
/* gap */
+
/* Words parallel to INPUT_ROUTE_0; All words that are active in INPUT_ROUTE_0
-// are set to a swizzling bit pattern, other words are 0.
-//
-// In immediate mode, the pattern is always set to xyzw. In vertex array
-// mode, the swizzling pattern is e.g. used to set zw components in texture
-// coordinates with only tweo components. */
+ * are set to a swizzling bit pattern, other words are 0.
+ *
+ * In immediate mode, the pattern is always set to xyzw. In vertex array
+ * mode, the swizzling pattern is e.g. used to set zw components in texture
+ * coordinates with only tweo components.
+ */
#define R300_VAP_INPUT_ROUTE_1_0 0x21E0
# define R300_INPUT_ROUTE_SELECT_X 0
# define R300_INPUT_ROUTE_SELECT_Y 1
@@ -210,11 +232,11 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_INPUT_ROUTE_SELECT_ZERO 4
# define R300_INPUT_ROUTE_SELECT_ONE 5
# define R300_INPUT_ROUTE_SELECT_MASK 7
-# define R300_INPUT_ROUTE_X_SHIFT 0
-# define R300_INPUT_ROUTE_Y_SHIFT 3
-# define R300_INPUT_ROUTE_Z_SHIFT 6
-# define R300_INPUT_ROUTE_W_SHIFT 9
-# define R300_INPUT_ROUTE_ENABLE (15 << 12)
+# define R300_INPUT_ROUTE_X_SHIFT 0
+# define R300_INPUT_ROUTE_Y_SHIFT 3
+# define R300_INPUT_ROUTE_Z_SHIFT 6
+# define R300_INPUT_ROUTE_W_SHIFT 9
+# define R300_INPUT_ROUTE_ENABLE (15 << 12)
#define R300_VAP_INPUT_ROUTE_1_1 0x21E4
#define R300_VAP_INPUT_ROUTE_1_2 0x21E8
#define R300_VAP_INPUT_ROUTE_1_3 0x21EC
@@ -223,53 +245,64 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_VAP_INPUT_ROUTE_1_6 0x21F8
#define R300_VAP_INPUT_ROUTE_1_7 0x21FC
-/* END */
+/* END: Vertex data assembly */
/* gap */
-/* BEGIN: Upload vertex program and data
-// The programmable vertex shader unit has a memory bank of unknown size
-// that can be written to in 16 byte units by writing the address into
-// UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs).
-//
-// Pointers into the memory bank are always in multiples of 16 bytes.
-//
-// The memory bank is divided into areas with fixed meaning.
-//
-// Starting at address UPLOAD_PROGRAM: Vertex program instructions.
-// Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB),
-// whereas the difference between known addresses suggests size 512.
-//
-// Starting at address UPLOAD_PARAMETERS: Vertex program parameters.
-// Native reported limits and the VPI layout suggest size 256, whereas
-// difference between known addresses suggests size 512.
-//
-// At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the
-// floating point pointsize. The exact purpose of this state is uncertain,
-// as there is also the R300_RE_POINTSIZE register.
-//
-// Multiple vertex programs and parameter sets can be loaded at once,
-// which could explain the size discrepancy. */
+
+/* BEGIN: Upload vertex program and data */
+
+/*
+ * The programmable vertex shader unit has a memory bank of unknown size
+ * that can be written to in 16 byte units by writing the address into
+ * UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs).
+ *
+ * Pointers into the memory bank are always in multiples of 16 bytes.
+ *
+ * The memory bank is divided into areas with fixed meaning.
+ *
+ * Starting at address UPLOAD_PROGRAM: Vertex program instructions.
+ * Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB),
+ * whereas the difference between known addresses suggests size 512.
+ *
+ * Starting at address UPLOAD_PARAMETERS: Vertex program parameters.
+ * Native reported limits and the VPI layout suggest size 256, whereas
+ * difference between known addresses suggests size 512.
+ *
+ * At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the
+ * floating point pointsize. The exact purpose of this state is uncertain,
+ * as there is also the R300_RE_POINTSIZE register.
+ *
+ * Multiple vertex programs and parameter sets can be loaded at once,
+ * which could explain the size discrepancy.
+ */
#define R300_VAP_PVS_UPLOAD_ADDRESS 0x2200
# define R300_PVS_UPLOAD_PROGRAM 0x00000000
# define R300_PVS_UPLOAD_PARAMETERS 0x00000200
# define R300_PVS_UPLOAD_POINTSIZE 0x00000406
+
/* gap */
+
#define R300_VAP_PVS_UPLOAD_DATA 0x2208
-/* END */
+
+/* END: Upload vertex program and data */
/* gap */
+
/* I do not know the purpose of this register. However, I do know that
-// it is set to 221C_CLEAR for clear operations and to 221C_NORMAL
-// for normal rendering. */
+ * it is set to 221C_CLEAR for clear operations and to 221C_NORMAL
+ * for normal rendering.
+ */
#define R300_VAP_UNKNOWN_221C 0x221C
# define R300_221C_NORMAL 0x00000000
# define R300_221C_CLEAR 0x0001C000
/* gap */
+
/* Sometimes, END_OF_PKT and 0x2284=0 are the only commands sent between
-// rendering commands and overwriting vertex program parameters.
-// Therefore, I suspect writing zero to 0x2284 synchronizes the engine and
-// avoids bugs caused by still running shaders reading bad data from memory. */
+ * rendering commands and overwriting vertex program parameters.
+ * Therefore, I suspect writing zero to 0x2284 synchronizes the engine and
+ * avoids bugs caused by still running shaders reading bad data from memory.
+ */
#define R300_VAP_PVS_WAITIDLE 0x2284 /* GUESS */
/* Absolutely no clue what this register is about. */
@@ -278,19 +311,22 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_2288_RV350 0x0000FFFF /* -- Vladimir */
/* gap */
+
/* Addresses are relative to the vertex program instruction area of the
-// memory bank. PROGRAM_END points to the last instruction of the active
-// program
-//
-// The meaning of the two UNKNOWN fields is obviously not known. However,
-// experiments so far have shown that both *must* point to an instruction
-// inside the vertex program, otherwise the GPU locks up.
-// fglrx usually sets CNTL_3_UNKNOWN to the end of the program and
-// CNTL_1_UNKNOWN points to instruction where last write to position takes place.
-// Most likely this is used to ignore rest of the program in cases where group of verts arent visible.
-// For some reason this "section" is sometimes accepted other instruction that have
-// no relationship with position calculations.
-*/
+ * memory bank. PROGRAM_END points to the last instruction of the active
+ * program
+ *
+ * The meaning of the two UNKNOWN fields is obviously not known. However,
+ * experiments so far have shown that both *must* point to an instruction
+ * inside the vertex program, otherwise the GPU locks up.
+ * fglrx usually sets CNTL_3_UNKNOWN to the end of the program and
+ * CNTL_1_UNKNOWN points to instruction where last write to position takes
+ * place.
+ * Most likely this is used to ignore rest of the program in cases
+ * where group of verts arent visible. For some reason this "section"
+ * is sometimes accepted other instruction that have no relationship with
+ *position calculations.
+ */
#define R300_VAP_PVS_CNTL_1 0x22D0
# define R300_PVS_CNTL_1_PROGRAM_START_SHIFT 0
# define R300_PVS_CNTL_1_POS_END_SHIFT 10
@@ -304,7 +340,8 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_PVS_CNTL_3_PROGRAM_UNKNOWN2_SHIFT 0
/* The entire range from 0x2300 to 0x2AC inclusive seems to be used for
-// immediate vertices */
+ * immediate vertices
+ */
#define R300_VAP_VTX_COLOR_R 0x2464
#define R300_VAP_VTX_COLOR_G 0x2468
#define R300_VAP_VTX_COLOR_B 0x246C
@@ -314,13 +351,15 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_VAP_VTX_POS_0_X_2 0x24A0 /* used for glVertex3*() */
#define R300_VAP_VTX_POS_0_Y_2 0x24A4
#define R300_VAP_VTX_POS_0_Z_2 0x24A8
-#define R300_VAP_VTX_END_OF_PKT 0x24AC /* write 0 to indicate end of packet? */
+/* write 0 to indicate end of packet? */
+#define R300_VAP_VTX_END_OF_PKT 0x24AC
/* gap */
/* These are values from r300_reg/r300_reg.h - they are known to be correct
- and are here so we can use one register file instead of several
- - Vladimir */
+ * and are here so we can use one register file instead of several
+ * - Vladimir
+ */
#define R300_GB_VAP_RASTER_VTX_FMT_0 0x4000
# define R300_GB_VAP_RASTER_VTX_FMT_0__POS_PRESENT (1<<0)
# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_0_PRESENT (1<<1)
@@ -343,14 +382,16 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21
/* UNK30 seems to enables point to quad transformation on textures
- (or something closely related to that).
- This bit is rather fatal at the time being due to lackings at pixel shader side */
+ * (or something closely related to that).
+ * This bit is rather fatal at the time being due to lackings at pixel
+ * shader side
+ */
#define R300_GB_ENABLE 0x4008
# define R300_GB_POINT_STUFF_ENABLE (1<<0)
# define R300_GB_LINE_STUFF_ENABLE (1<<1)
# define R300_GB_TRIANGLE_STUFF_ENABLE (1<<2)
# define R300_GB_STENCIL_AUTO_ENABLE (1<<4)
-# define R300_GB_UNK30 (1<<30)
+# define R300_GB_UNK31 (1<<31)
/* each of the following is 2 bits wide */
#define R300_GB_TEX_REPLICATE 0
#define R300_GB_TEX_ST 1
@@ -391,6 +432,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_GB_TILE_PIPE_COUNT_RV300 0
# define R300_GB_TILE_PIPE_COUNT_R300 (3<<1)
# define R300_GB_TILE_PIPE_COUNT_R420 (7<<1)
+# define R300_GB_TILE_PIPE_COUNT_RV410 (3<<1)
# define R300_GB_TILE_SIZE_8 0
# define R300_GB_TILE_SIZE_16 (1<<4)
# define R300_GB_TILE_SIZE_32 (2<<4)
@@ -451,9 +493,8 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_AA_SUBSAMPLES_4 (2<<1)
# define R300_AA_SUBSAMPLES_6 (3<<1)
-/* END */
-
/* gap */
+
/* Zero to flush caches. */
#define R300_TX_CNTL 0x4100
@@ -477,8 +518,9 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_TX_ENABLE_15 (1 << 15)
/* The pointsize is given in multiples of 6. The pointsize can be
-// enormous: Clear() renders a single point that fills the entire
-// framebuffer. */
+ * enormous: Clear() renders a single point that fills the entire
+ * framebuffer.
+ */
#define R300_RE_POINTSIZE 0x421C
# define R300_POINTSIZE_Y_SHIFT 0
# define R300_POINTSIZE_Y_MASK (0xFFFF << 0) /* GUESS */
@@ -487,11 +529,11 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_POINTSIZE_MAX (R300_POINTSIZE_Y_MASK / 6)
/* The line width is given in multiples of 6.
- In default mode lines are classified as vertical lines.
- HO: horizontal
- VE: vertical or horizontal
- HO & VE: no classification
-*/
+ * In default mode lines are classified as vertical lines.
+ * HO: horizontal
+ * VE: vertical or horizontal
+ * HO & VE: no classification
+ */
#define R300_RE_LINE_CNT 0x4234
# define R300_LINESIZE_SHIFT 0
# define R300_LINESIZE_MASK (0xFFFF << 0) /* GUESS */
@@ -502,6 +544,9 @@ I am fairly certain that they are correct unless stated otherwise in comments.
/* Some sort of scale or clamp value for texcoordless textures. */
#define R300_RE_UNK4238 0x4238
+/* Something shade related */
+#define R300_RE_SHADE 0x4274
+
#define R300_RE_SHADE_MODEL 0x4278
# define R300_RE_SHADE_MODEL_SMOOTH 0x3aaaa
# define R300_RE_SHADE_MODEL_FLAT 0x39595
@@ -516,24 +561,30 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_PM_BACK_LINE (1 << 7)
# define R300_PM_BACK_FILL (1 << 8)
+/* Fog parameters */
+#define R300_RE_FOG_SCALE 0x4294
+#define R300_RE_FOG_START 0x4298
+
/* Not sure why there are duplicate of factor and constant values.
- My best guess so far is that there are seperate zbiases for test and write.
- Ordering might be wrong.
- Some of the tests indicate that fgl has a fallback implementation of zbias
- via pixel shaders. */
+ * My best guess so far is that there are seperate zbiases for test and write.
+ * Ordering might be wrong.
+ * Some of the tests indicate that fgl has a fallback implementation of zbias
+ * via pixel shaders.
+ */
#define R300_RE_ZBIAS_T_FACTOR 0x42A4
#define R300_RE_ZBIAS_T_CONSTANT 0x42A8
#define R300_RE_ZBIAS_W_FACTOR 0x42AC
#define R300_RE_ZBIAS_W_CONSTANT 0x42B0
/* This register needs to be set to (1<<1) for RV350 to correctly
- perform depth test (see --vb-triangles in r300_demo)
- Don't know about other chips. - Vladimir
- This is set to 3 when GL_POLYGON_OFFSET_FILL is on.
- My guess is that there are two bits for each zbias primitive (FILL, LINE, POINT).
- One to enable depth test and one for depth write.
- Yet this doesnt explain why depth writes work ...
- */
+ * perform depth test (see --vb-triangles in r300_demo)
+ * Don't know about other chips. - Vladimir
+ * This is set to 3 when GL_POLYGON_OFFSET_FILL is on.
+ * My guess is that there are two bits for each zbias primitive
+ * (FILL, LINE, POINT).
+ * One to enable depth test and one for depth write.
+ * Yet this doesnt explain why depth writes work ...
+ */
#define R300_RE_OCCLUSION_CNTL 0x42B4
# define R300_OCCLUSION_ON (1<<1)
@@ -544,30 +595,37 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_FRONT_FACE_CW (1 << 2)
-/* BEGIN: Rasterization / Interpolators - many guesses
-// 0_UNKNOWN_18 has always been set except for clear operations.
-// TC_CNT is the number of incoming texture coordinate sets (i.e. it depends
-// on the vertex program, *not* the fragment program) */
+/* BEGIN: Rasterization / Interpolators - many guesses */
+
+/* 0_UNKNOWN_18 has always been set except for clear operations.
+ * TC_CNT is the number of incoming texture coordinate sets (i.e. it depends
+ * on the vertex program, *not* the fragment program)
+ */
#define R300_RS_CNTL_0 0x4300
# define R300_RS_CNTL_TC_CNT_SHIFT 2
# define R300_RS_CNTL_TC_CNT_MASK (7 << 2)
-# define R300_RS_CNTL_CI_CNT_SHIFT 7 /* number of color interpolators used */
+ /* number of color interpolators used */
+# define R300_RS_CNTL_CI_CNT_SHIFT 7
# define R300_RS_CNTL_0_UNKNOWN_18 (1 << 18)
-/* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n register. */
+ /* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n
+ register. */
#define R300_RS_CNTL_1 0x4304
/* gap */
+
/* Only used for texture coordinates.
-// Use the source field to route texture coordinate input from the vertex program
-// to the desired interpolator. Note that the source field is relative to the
-// outputs the vertex program *actually* writes. If a vertex program only writes
-// texcoord[1], this will be source index 0.
-// Set INTERP_USED on all interpolators that produce data used by the
-// fragment program. INTERP_USED looks like a swizzling mask, but
-// I haven't seen it used that way.
-//
-// Note: The _UNKNOWN constants are always set in their respective register.
-// I don't know if this is necessary. */
+ * Use the source field to route texture coordinate input from the
+ * vertex program to the desired interpolator. Note that the source
+ * field is relative to the outputs the vertex program *actually*
+ * writes. If a vertex program only writes texcoord[1], this will
+ * be source index 0.
+ * Set INTERP_USED on all interpolators that produce data used by
+ * the fragment program. INTERP_USED looks like a swizzling mask,
+ * but I haven't seen it used that way.
+ *
+ * Note: The _UNKNOWN constants are always set in their respective
+ * register. I don't know if this is necessary.
+ */
#define R300_RS_INTERP_0 0x4310
#define R300_RS_INTERP_1 0x4314
# define R300_RS_INTERP_1_UNKNOWN 0x40
@@ -584,7 +642,8 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_RS_INTERP_USED 0x00D10000
/* These DWORDs control how vertex data is routed into fragment program
-// registers, after interpolators. */
+ * registers, after interpolators.
+ */
#define R300_RS_ROUTE_0 0x4330
#define R300_RS_ROUTE_1 0x4334
#define R300_RS_ROUTE_2 0x4338
@@ -606,8 +665,9 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_RS_ROUTE_DEST_MASK (31 << 6) /* GUESS */
/* Special handling for color: When the fragment program uses color,
-// the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the
-// color register index. */
+ * the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the
+ * color register index.
+ */
# define R300_RS_ROUTE_0_COLOR (1 << 14)
# define R300_RS_ROUTE_0_COLOR_DEST_SHIFT 17
# define R300_RS_ROUTE_0_COLOR_DEST_MASK (31 << 17) /* GUESS */
@@ -616,22 +676,24 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_RS_ROUTE_1_COLOR1_DEST_SHIFT 17
# define R300_RS_ROUTE_1_COLOR1_DEST_MASK (31 << 17)
# define R300_RS_ROUTE_1_UNKNOWN11 (1 << 11)
-/* END */
-
-/* BEGIN: Scissors and cliprects
-// There are four clipping rectangles. Their corner coordinates are inclusive.
-// Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending
-// on whether the pixel is inside cliprects 0-3, respectively. For example,
-// if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned
-// the number 3 (binary 0011).
-// Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set,
-// the pixel is rasterized.
-//
-// In addition to this, there is a scissors rectangle. Only pixels inside the
-// scissors rectangle are drawn. (coordinates are inclusive)
-//
-// For some reason, the top-left corner of the framebuffer is at (1440, 1440)
-// for the purpose of clipping and scissors. */
+/* END: Rasterization / Interpolators - many guesses */
+
+/* BEGIN: Scissors and cliprects */
+
+/* There are four clipping rectangles. Their corner coordinates are inclusive.
+ * Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending
+ * on whether the pixel is inside cliprects 0-3, respectively. For example,
+ * if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned
+ * the number 3 (binary 0011).
+ * Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set,
+ * the pixel is rasterized.
+ *
+ * In addition to this, there is a scissors rectangle. Only pixels inside the
+ * scissors rectangle are drawn. (coordinates are inclusive)
+ *
+ * For some reason, the top-left corner of the framebuffer is at (1440, 1440)
+ * for the purpose of clipping and scissors.
+ */
#define R300_RE_CLIPRECT_TL_0 0x43B0
#define R300_RE_CLIPRECT_BR_0 0x43B4
#define R300_RE_CLIPRECT_TL_1 0x43B8
@@ -665,6 +727,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_CLIP_3210 (1 << 15)
/* gap */
+
#define R300_RE_SCISSORS_TL 0x43E0
#define R300_RE_SCISSORS_BR 0x43E4
# define R300_SCISSORS_OFFSET 1440
@@ -672,12 +735,15 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_SCISSORS_X_MASK (0x1FFF << 0)
# define R300_SCISSORS_Y_SHIFT 13
# define R300_SCISSORS_Y_MASK (0x1FFF << 13)
-/* END */
+/* END: Scissors and cliprects */
-/* BEGIN: Texture specification
-// The texture specification dwords are grouped by meaning and not by texture unit.
-// This means that e.g. the offset for texture image unit N is found in register
-// TX_OFFSET_0 + (4*N) */
+/* BEGIN: Texture specification */
+
+/*
+ * The texture specification dwords are grouped by meaning and not by texture
+ * unit. This means that e.g. the offset for texture image unit N is found in
+ * register TX_OFFSET_0 + (4*N)
+ */
#define R300_TX_FILTER_0 0x4400
# define R300_TX_REPEAT 0
# define R300_TX_MIRRORED 1
@@ -701,13 +767,14 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_TX_MIN_FILTER_LINEAR_MIP_LINEAR (10 << 11)
/* NOTE: NEAREST doesnt seem to exist.
- Im not seting MAG_FILTER_MASK and (3 << 11) on for all
- anisotropy modes because that would void selected mag filter */
-# define R300_TX_MIN_FILTER_ANISO_NEAREST ((0 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/)
-# define R300_TX_MIN_FILTER_ANISO_LINEAR ((0 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/)
-# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST ((1 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/)
-# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR ((2 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/)
-# define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) )
+ * Im not seting MAG_FILTER_MASK and (3 << 11) on for all
+ * anisotropy modes because that would void selected mag filter
+ */
+# define R300_TX_MIN_FILTER_ANISO_NEAREST (0 << 13)
+# define R300_TX_MIN_FILTER_ANISO_LINEAR (0 << 13)
+# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST (1 << 13)
+# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR (2 << 13)
+# define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) )
# define R300_TX_MAX_ANISO_1_TO_1 (0 << 21)
# define R300_TX_MAX_ANISO_2_TO_1 (2 << 21)
# define R300_TX_MAX_ANISO_4_TO_1 (4 << 21)
@@ -738,10 +805,10 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_TX_HEIGHTMASK_SHIFT 11
# define R300_TX_HEIGHTMASK_MASK (2047 << 11)
# define R300_TX_UNK23 (1 << 23)
-# define R300_TX_SIZE_SHIFT 26 /* largest of width, height */
-# define R300_TX_SIZE_MASK (15 << 26)
-# define R300_TX_SIZE_PROJECTED (1<<30)
-# define R300_TX_SIZE_TXPITCH_EN (1<<31)
+# define R300_TX_MAX_MIP_LEVEL_SHIFT 26
+# define R300_TX_MAX_MIP_LEVEL_MASK (0xf << 26)
+# define R300_TX_SIZE_PROJECTED (1<<30)
+# define R300_TX_SIZE_TXPITCH_EN (1<<31)
#define R300_TX_FORMAT_0 0x44C0
/* The interpretation of the format word by Wladimir van der Laan */
/* The X, Y, Z and W refer to the layout of the components.
@@ -769,7 +836,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_TX_FORMAT_A8R8G8B8 0x13 /* no swizzle */
# define R300_TX_FORMAT_B8G8_B8G8 0x14 /* no swizzle */
# define R300_TX_FORMAT_G8R8_G8B8 0x15 /* no swizzle */
- /* 0x16 - some 16 bit green format.. ?? */
+ /* 0x16 - some 16 bit green format.. ?? */
# define R300_TX_FORMAT_UNK25 (1 << 25) /* no swizzle */
# define R300_TX_FORMAT_CUBIC_MAP (1 << 26)
@@ -797,23 +864,26 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_TX_FORMAT_W 3
# define R300_TX_FORMAT_ZERO 4
# define R300_TX_FORMAT_ONE 5
-# define R300_TX_FORMAT_CUT_Z 6 /* 2.0*Z, everything above 1.0 is set to 0.0 */
-# define R300_TX_FORMAT_CUT_W 7 /* 2.0*W, everything above 1.0 is set to 0.0 */
+ /* 2.0*Z, everything above 1.0 is set to 0.0 */
+# define R300_TX_FORMAT_CUT_Z 6
+ /* 2.0*W, everything above 1.0 is set to 0.0 */
+# define R300_TX_FORMAT_CUT_W 7
# define R300_TX_FORMAT_B_SHIFT 18
# define R300_TX_FORMAT_G_SHIFT 15
# define R300_TX_FORMAT_R_SHIFT 12
# define R300_TX_FORMAT_A_SHIFT 9
/* Convenience macro to take care of layout and swizzling */
-# define R300_EASY_TX_FORMAT(B, G, R, A, FMT) (\
- ((R300_TX_FORMAT_##B)<<R300_TX_FORMAT_B_SHIFT) \
- | ((R300_TX_FORMAT_##G)<<R300_TX_FORMAT_G_SHIFT) \
- | ((R300_TX_FORMAT_##R)<<R300_TX_FORMAT_R_SHIFT) \
- | ((R300_TX_FORMAT_##A)<<R300_TX_FORMAT_A_SHIFT) \
- | (R300_TX_FORMAT_##FMT) \
- )
- /* These can be ORed with result of R300_EASY_TX_FORMAT() */
- /* We don't really know what they do. Take values from a constant color ? */
+# define R300_EASY_TX_FORMAT(B, G, R, A, FMT) ( \
+ ((R300_TX_FORMAT_##B)<<R300_TX_FORMAT_B_SHIFT) \
+ | ((R300_TX_FORMAT_##G)<<R300_TX_FORMAT_G_SHIFT) \
+ | ((R300_TX_FORMAT_##R)<<R300_TX_FORMAT_R_SHIFT) \
+ | ((R300_TX_FORMAT_##A)<<R300_TX_FORMAT_A_SHIFT) \
+ | (R300_TX_FORMAT_##FMT) \
+ )
+ /* These can be ORed with result of R300_EASY_TX_FORMAT()
+ We don't really know what they do. Take values from a
+ constant color ? */
# define R300_TX_FORMAT_CONST_X (1<<5)
# define R300_TX_FORMAT_CONST_Y (2<<5)
# define R300_TX_FORMAT_CONST_Z (4<<5)
@@ -823,7 +893,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_TX_PITCH_0 0x4500 /* obvious missing in gap */
#define R300_TX_OFFSET_0 0x4540
-/* BEGIN: Guess from R200 */
+ /* BEGIN: Guess from R200 */
# define R300_TXO_ENDIAN_NO_SWAP (0 << 0)
# define R300_TXO_ENDIAN_BYTE_SWAP (1 << 0)
# define R300_TXO_ENDIAN_WORD_SWAP (2 << 0)
@@ -832,53 +902,62 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_TXO_MICRO_TILE (1 << 3)
# define R300_TXO_OFFSET_MASK 0xffffffe0
# define R300_TXO_OFFSET_SHIFT 5
-/* END */
-#define R300_TX_CHROMA_KEY_0 0x4580 /* 32 bit chroma key */
-#define R300_TX_BORDER_COLOR_0 0x45C0 //ff00ff00 == { 0, 1.0, 0, 1.0 }
-
-/* END */
-
-/* BEGIN: Fragment program instruction set
-// Fragment programs are written directly into register space.
-// There are separate instruction streams for texture instructions and ALU
-// instructions.
-// In order to synchronize these streams, the program is divided into up
-// to 4 nodes. Each node begins with a number of TEX operations, followed
-// by a number of ALU operations.
-// The first node can have zero TEX ops, all subsequent nodes must have at least
-// one TEX ops.
-// All nodes must have at least one ALU op.
-//
-// The index of the last node is stored in PFS_CNTL_0: A value of 0 means
-// 1 node, a value of 3 means 4 nodes.
-// The total amount of instructions is defined in PFS_CNTL_2. The offsets are
-// offsets into the respective instruction streams, while *_END points to the
-// last instruction relative to this offset. */
+ /* END: Guess from R200 */
+
+/* 32 bit chroma key */
+#define R300_TX_CHROMA_KEY_0 0x4580
+/* ff00ff00 == { 0, 1.0, 0, 1.0 } */
+#define R300_TX_BORDER_COLOR_0 0x45C0
+
+/* END: Texture specification */
+
+/* BEGIN: Fragment program instruction set */
+
+/* Fragment programs are written directly into register space.
+ * There are separate instruction streams for texture instructions and ALU
+ * instructions.
+ * In order to synchronize these streams, the program is divided into up
+ * to 4 nodes. Each node begins with a number of TEX operations, followed
+ * by a number of ALU operations.
+ * The first node can have zero TEX ops, all subsequent nodes must have at
+ * least
+ * one TEX ops.
+ * All nodes must have at least one ALU op.
+ *
+ * The index of the last node is stored in PFS_CNTL_0: A value of 0 means
+ * 1 node, a value of 3 means 4 nodes.
+ * The total amount of instructions is defined in PFS_CNTL_2. The offsets are
+ * offsets into the respective instruction streams, while *_END points to the
+ * last instruction relative to this offset.
+ */
#define R300_PFS_CNTL_0 0x4600
# define R300_PFS_CNTL_LAST_NODES_SHIFT 0
# define R300_PFS_CNTL_LAST_NODES_MASK (3 << 0)
# define R300_PFS_CNTL_FIRST_NODE_HAS_TEX (1 << 3)
#define R300_PFS_CNTL_1 0x4604
/* There is an unshifted value here which has so far always been equal to the
-// index of the highest used temporary register. */
+ * index of the highest used temporary register.
+ */
#define R300_PFS_CNTL_2 0x4608
# define R300_PFS_CNTL_ALU_OFFSET_SHIFT 0
# define R300_PFS_CNTL_ALU_OFFSET_MASK (63 << 0)
# define R300_PFS_CNTL_ALU_END_SHIFT 6
-# define R300_PFS_CNTL_ALU_END_MASK (63 << 0)
+# define R300_PFS_CNTL_ALU_END_MASK (63 << 6)
# define R300_PFS_CNTL_TEX_OFFSET_SHIFT 12
# define R300_PFS_CNTL_TEX_OFFSET_MASK (31 << 12) /* GUESS */
# define R300_PFS_CNTL_TEX_END_SHIFT 18
# define R300_PFS_CNTL_TEX_END_MASK (31 << 18) /* GUESS */
/* gap */
+
/* Nodes are stored backwards. The last active node is always stored in
-// PFS_NODE_3.
-// Example: In a 2-node program, NODE_0 and NODE_1 are set to 0. The
-// first node is stored in NODE_2, the second node is stored in NODE_3.
-//
-// Offsets are relative to the master offset from PFS_CNTL_2.
-// LAST_NODE is set for the last node, and only for the last node. */
+ * PFS_NODE_3.
+ * Example: In a 2-node program, NODE_0 and NODE_1 are set to 0. The
+ * first node is stored in NODE_2, the second node is stored in NODE_3.
+ *
+ * Offsets are relative to the master offset from PFS_CNTL_2.
+ * LAST_NODE is set for the last node, and only for the last node.
+ */
#define R300_PFS_NODE_0 0x4610
#define R300_PFS_NODE_1 0x4614
#define R300_PFS_NODE_2 0x4618
@@ -896,86 +975,93 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_PFS_NODE_OUTPUT_DEPTH (1 << 23)
/* TEX
-// As far as I can tell, texture instructions cannot write into output
-// registers directly. A subsequent ALU instruction is always necessary,
-// even if it's just MAD o0, r0, 1, 0 */
+ * As far as I can tell, texture instructions cannot write into output
+ * registers directly. A subsequent ALU instruction is always necessary,
+ * even if it's just MAD o0, r0, 1, 0
+ */
#define R300_PFS_TEXI_0 0x4620
-# define R300_FPITX_SRC_SHIFT 0
-# define R300_FPITX_SRC_MASK (31 << 0)
-# define R300_FPITX_SRC_CONST (1 << 5) /* GUESS */
-# define R300_FPITX_DST_SHIFT 6
-# define R300_FPITX_DST_MASK (31 << 6)
-# define R300_FPITX_IMAGE_SHIFT 11
-# define R300_FPITX_IMAGE_MASK (15 << 11) /* GUESS based on layout and native limits */
+# define R300_FPITX_SRC_SHIFT 0
+# define R300_FPITX_SRC_MASK (31 << 0)
+ /* GUESS */
+# define R300_FPITX_SRC_CONST (1 << 5)
+# define R300_FPITX_DST_SHIFT 6
+# define R300_FPITX_DST_MASK (31 << 6)
+# define R300_FPITX_IMAGE_SHIFT 11
+ /* GUESS based on layout and native limits */
+# define R300_FPITX_IMAGE_MASK (15 << 11)
/* Unsure if these are opcodes, or some kind of bitfield, but this is how
* they were set when I checked
*/
-# define R300_FPITX_OPCODE_SHIFT 15
-# define R300_FPITX_OP_TEX 1
-# define R300_FPITX_OP_KIL 2
-# define R300_FPITX_OP_TXP 3
-# define R300_FPITX_OP_TXB 4
+# define R300_FPITX_OPCODE_SHIFT 15
+# define R300_FPITX_OP_TEX 1
+# define R300_FPITX_OP_KIL 2
+# define R300_FPITX_OP_TXP 3
+# define R300_FPITX_OP_TXB 4
/* ALU
-// The ALU instructions register blocks are enumerated according to the order
-// in which fglrx. I assume there is space for 64 instructions, since
-// each block has space for a maximum of 64 DWORDs, and this matches reported
-// native limits.
-//
-// The basic functional block seems to be one MAD for each color and alpha,
-// and an adder that adds all components after the MUL.
-// - ADD, MUL, MAD etc.: use MAD with appropriate neutral operands
-// - DP4: Use OUTC_DP4, OUTA_DP4
-// - DP3: Use OUTC_DP3, OUTA_DP4, appropriate alpha operands
-// - DPH: Use OUTC_DP4, OUTA_DP4, appropriate alpha operands
-// - CMP: If ARG2 < 0, return ARG1, else return ARG0
-// - FLR: use FRC+MAD
-// - XPD: use MAD+MAD
-// - SGE, SLT: use MAD+CMP
-// - RSQ: use ABS modifier for argument
-// - Use OUTC_REPL_ALPHA to write results of an alpha-only operation (e.g. RCP)
-// into color register
-// - apparently, there's no quick DST operation
-// - fglrx set FPI2_UNKNOWN_31 on a "MAD fragment.color, tmp0, tmp1, tmp2"
-// - fglrx set FPI2_UNKNOWN_31 on a "MAX r2, r1, c0"
-// - fglrx once set FPI0_UNKNOWN_31 on a "FRC r1, r1"
-//
-// Operand selection
-// First stage selects three sources from the available registers and
-// constant parameters. This is defined in INSTR1 (color) and INSTR3 (alpha).
-// fglrx sorts the three source fields: Registers before constants,
-// lower indices before higher indices; I do not know whether this is necessary.
-// fglrx fills unused sources with "read constant 0"
-// According to specs, you cannot select more than two different constants.
-//
-// Second stage selects the operands from the sources. This is defined in
-// INSTR0 (color) and INSTR2 (alpha). You can also select the special constants
-// zero and one.
-// Swizzling and negation happens in this stage, as well.
-//
-// Important: Color and alpha seem to be mostly separate, i.e. their sources
-// selection appears to be fully independent (the register storage is probably
-// physically split into a color and an alpha section).
-// However (because of the apparent physical split), there is some interaction
-// WRT swizzling. If, for example, you want to load an R component into an
-// Alpha operand, this R component is taken from a *color* source, not from
-// an alpha source. The corresponding register doesn't even have to appear in
-// the alpha sources list. (I hope this alll makes sense to you)
-//
-// Destination selection
-// The destination register index is in FPI1 (color) and FPI3 (alpha) together
-// with enable bits.
-// There are separate enable bits for writing into temporary registers
-// (DSTC_REG_* /DSTA_REG) and and program output registers (DSTC_OUTPUT_* /DSTA_OUTPUT).
-// You can write to both at once, or not write at all (the same index
-// must be used for both).
-//
-// Note: There is a special form for LRP
-// - Argument order is the same as in ARB_fragment_program.
-// - Operation is MAD
-// - ARG1 is set to ARGC_SRC1C_LRP/ARGC_SRC1A_LRP
-// - Set FPI0/FPI2_SPECIAL_LRP
-// Arbitrary LRP (including support for swizzling) requires vanilla MAD+MAD */
+ * The ALU instructions register blocks are enumerated according to the order
+ * in which fglrx. I assume there is space for 64 instructions, since
+ * each block has space for a maximum of 64 DWORDs, and this matches reported
+ * native limits.
+ *
+ * The basic functional block seems to be one MAD for each color and alpha,
+ * and an adder that adds all components after the MUL.
+ * - ADD, MUL, MAD etc.: use MAD with appropriate neutral operands
+ * - DP4: Use OUTC_DP4, OUTA_DP4
+ * - DP3: Use OUTC_DP3, OUTA_DP4, appropriate alpha operands
+ * - DPH: Use OUTC_DP4, OUTA_DP4, appropriate alpha operands
+ * - CMPH: If ARG2 > 0.5, return ARG0, else return ARG1
+ * - CMP: If ARG2 < 0, return ARG1, else return ARG0
+ * - FLR: use FRC+MAD
+ * - XPD: use MAD+MAD
+ * - SGE, SLT: use MAD+CMP
+ * - RSQ: use ABS modifier for argument
+ * - Use OUTC_REPL_ALPHA to write results of an alpha-only operation
+ * (e.g. RCP) into color register
+ * - apparently, there's no quick DST operation
+ * - fglrx set FPI2_UNKNOWN_31 on a "MAD fragment.color, tmp0, tmp1, tmp2"
+ * - fglrx set FPI2_UNKNOWN_31 on a "MAX r2, r1, c0"
+ * - fglrx once set FPI0_UNKNOWN_31 on a "FRC r1, r1"
+ *
+ * Operand selection
+ * First stage selects three sources from the available registers and
+ * constant parameters. This is defined in INSTR1 (color) and INSTR3 (alpha).
+ * fglrx sorts the three source fields: Registers before constants,
+ * lower indices before higher indices; I do not know whether this is
+ * necessary.
+ *
+ * fglrx fills unused sources with "read constant 0"
+ * According to specs, you cannot select more than two different constants.
+ *
+ * Second stage selects the operands from the sources. This is defined in
+ * INSTR0 (color) and INSTR2 (alpha). You can also select the special constants
+ * zero and one.
+ * Swizzling and negation happens in this stage, as well.
+ *
+ * Important: Color and alpha seem to be mostly separate, i.e. their sources
+ * selection appears to be fully independent (the register storage is probably
+ * physically split into a color and an alpha section).
+ * However (because of the apparent physical split), there is some interaction
+ * WRT swizzling. If, for example, you want to load an R component into an
+ * Alpha operand, this R component is taken from a *color* source, not from
+ * an alpha source. The corresponding register doesn't even have to appear in
+ * the alpha sources list. (I hope this alll makes sense to you)
+ *
+ * Destination selection
+ * The destination register index is in FPI1 (color) and FPI3 (alpha)
+ * together with enable bits.
+ * There are separate enable bits for writing into temporary registers
+ * (DSTC_REG_* /DSTA_REG) and and program output registers (DSTC_OUTPUT_*
+ * /DSTA_OUTPUT). You can write to both at once, or not write at all (the
+ * same index must be used for both).
+ *
+ * Note: There is a special form for LRP
+ * - Argument order is the same as in ARB_fragment_program.
+ * - Operation is MAD
+ * - ARG1 is set to ARGC_SRC1C_LRP/ARGC_SRC1A_LRP
+ * - Set FPI0/FPI2_SPECIAL_LRP
+ * Arbitrary LRP (including support for swizzling) requires vanilla MAD+MAD
+ */
#define R300_PFS_INSTR1_0 0x46C0
# define R300_FPI1_SRC0C_SHIFT 0
# define R300_FPI1_SRC0C_MASK (31 << 0)
@@ -1032,7 +1118,8 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_FPI0_ARGC_SRC1C_LRP 15
# define R300_FPI0_ARGC_ZERO 20
# define R300_FPI0_ARGC_ONE 21
-# define R300_FPI0_ARGC_HALF 22 /* GUESS */
+ /* GUESS */
+# define R300_FPI0_ARGC_HALF 22
# define R300_FPI0_ARGC_SRC0C_YZX 23
# define R300_FPI0_ARGC_SRC1C_YZX 24
# define R300_FPI0_ARGC_SRC2C_YZX 25
@@ -1061,6 +1148,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_FPI0_OUTC_DP4 (2 << 23)
# define R300_FPI0_OUTC_MIN (4 << 23)
# define R300_FPI0_OUTC_MAX (5 << 23)
+# define R300_FPI0_OUTC_CMPH (7 << 23)
# define R300_FPI0_OUTC_CMP (8 << 23)
# define R300_FPI0_OUTC_FRC (9 << 23)
# define R300_FPI0_OUTC_REPL_ALPHA (10 << 23)
@@ -1083,20 +1171,23 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_FPI2_ARGA_SRC1A_LRP 15
# define R300_FPI2_ARGA_ZERO 16
# define R300_FPI2_ARGA_ONE 17
-# define R300_FPI2_ARGA_HALF 18 /* GUESS */
-
+ /* GUESS */
+# define R300_FPI2_ARGA_HALF 18
# define R300_FPI2_ARG0A_SHIFT 0
# define R300_FPI2_ARG0A_MASK (31 << 0)
# define R300_FPI2_ARG0A_NEG (1 << 5)
-# define R300_FPI2_ARG0A_ABS (1 << 6) /* GUESS */
+ /* GUESS */
+# define R300_FPI2_ARG0A_ABS (1 << 6)
# define R300_FPI2_ARG1A_SHIFT 7
# define R300_FPI2_ARG1A_MASK (31 << 7)
# define R300_FPI2_ARG1A_NEG (1 << 12)
-# define R300_FPI2_ARG1A_ABS (1 << 13) /* GUESS */
+ /* GUESS */
+# define R300_FPI2_ARG1A_ABS (1 << 13)
# define R300_FPI2_ARG2A_SHIFT 14
# define R300_FPI2_ARG2A_MASK (31 << 14)
# define R300_FPI2_ARG2A_NEG (1 << 19)
-# define R300_FPI2_ARG2A_ABS (1 << 20) /* GUESS */
+ /* GUESS */
+# define R300_FPI2_ARG2A_ABS (1 << 20)
# define R300_FPI2_SPECIAL_LRP (1 << 21)
# define R300_FPI2_OUTA_MAD (0 << 23)
# define R300_FPI2_OUTA_DP4 (1 << 23)
@@ -1110,9 +1201,19 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_FPI2_OUTA_RSQ (11 << 23)
# define R300_FPI2_OUTA_SAT (1 << 30)
# define R300_FPI2_UNKNOWN_31 (1 << 31)
-/* END */
+/* END: Fragment program instruction set */
+
+/* Fog state and color */
+#define R300_RE_FOG_STATE 0x4BC0
+# define R300_FOG_ENABLE (1 << 0)
+# define R300_FOG_MODE_LINEAR (0 << 1)
+# define R300_FOG_MODE_EXP (1 << 1)
+# define R300_FOG_MODE_EXP2 (2 << 1)
+# define R300_FOG_MODE_MASK (3 << 1)
+#define R300_FOG_COLOR_R 0x4BC8
+#define R300_FOG_COLOR_G 0x4BCC
+#define R300_FOG_COLOR_B 0x4BD0
-/* gap */
#define R300_PP_ALPHA_TEST 0x4BD4
# define R300_REF_ALPHA_MASK 0x000000ff
# define R300_ALPHA_TEST_FAIL (0 << 8)
@@ -1127,6 +1228,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_ALPHA_TEST_ENABLE (1 << 11)
/* gap */
+
/* Fragment program parameters in 7.16 floating point */
#define R300_PFS_PARAM_0_X 0x4C00
#define R300_PFS_PARAM_0_Y 0x4C04
@@ -1139,45 +1241,48 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_PFS_PARAM_31_W 0x4DFC
/* Notes:
-// - AFAIK fglrx always sets BLEND_UNKNOWN when blending is used in the application
-// - AFAIK fglrx always sets BLEND_NO_SEPARATE when CBLEND and ABLEND are set to the same
-// function (both registers are always set up completely in any case)
-// - Most blend flags are simply copied from R200 and not tested yet */
+ * - AFAIK fglrx always sets BLEND_UNKNOWN when blending is used in
+ * the application
+ * - AFAIK fglrx always sets BLEND_NO_SEPARATE when CBLEND and ABLEND
+ * are set to the same
+ * function (both registers are always set up completely in any case)
+ * - Most blend flags are simply copied from R200 and not tested yet
+ */
#define R300_RB3D_CBLEND 0x4E04
#define R300_RB3D_ABLEND 0x4E08
- /* the following only appear in CBLEND */
+/* the following only appear in CBLEND */
# define R300_BLEND_ENABLE (1 << 0)
# define R300_BLEND_UNKNOWN (3 << 1)
# define R300_BLEND_NO_SEPARATE (1 << 3)
- /* the following are shared between CBLEND and ABLEND */
+/* the following are shared between CBLEND and ABLEND */
# define R300_FCN_MASK (3 << 12)
# define R300_COMB_FCN_ADD_CLAMP (0 << 12)
# define R300_COMB_FCN_ADD_NOCLAMP (1 << 12)
# define R300_COMB_FCN_SUB_CLAMP (2 << 12)
# define R300_COMB_FCN_SUB_NOCLAMP (3 << 12)
-# define R300_SRC_BLEND_GL_ZERO (32 << 16)
-# define R300_SRC_BLEND_GL_ONE (33 << 16)
-# define R300_SRC_BLEND_GL_SRC_COLOR (34 << 16)
-# define R300_SRC_BLEND_GL_ONE_MINUS_SRC_COLOR (35 << 16)
-# define R300_SRC_BLEND_GL_DST_COLOR (36 << 16)
-# define R300_SRC_BLEND_GL_ONE_MINUS_DST_COLOR (37 << 16)
-# define R300_SRC_BLEND_GL_SRC_ALPHA (38 << 16)
-# define R300_SRC_BLEND_GL_ONE_MINUS_SRC_ALPHA (39 << 16)
-# define R300_SRC_BLEND_GL_DST_ALPHA (40 << 16)
-# define R300_SRC_BLEND_GL_ONE_MINUS_DST_ALPHA (41 << 16)
-# define R300_SRC_BLEND_GL_SRC_ALPHA_SATURATE (42 << 16)
-# define R300_SRC_BLEND_MASK (63 << 16)
-# define R300_DST_BLEND_GL_ZERO (32 << 24)
-# define R300_DST_BLEND_GL_ONE (33 << 24)
-# define R300_DST_BLEND_GL_SRC_COLOR (34 << 24)
-# define R300_DST_BLEND_GL_ONE_MINUS_SRC_COLOR (35 << 24)
-# define R300_DST_BLEND_GL_DST_COLOR (36 << 24)
-# define R300_DST_BLEND_GL_ONE_MINUS_DST_COLOR (37 << 24)
-# define R300_DST_BLEND_GL_SRC_ALPHA (38 << 24)
-# define R300_DST_BLEND_GL_ONE_MINUS_SRC_ALPHA (39 << 24)
-# define R300_DST_BLEND_GL_DST_ALPHA (40 << 24)
-# define R300_DST_BLEND_GL_ONE_MINUS_DST_ALPHA (41 << 24)
-# define R300_DST_BLEND_MASK (63 << 24)
+# define R300_COMB_FCN_MIN (4 << 12)
+# define R300_COMB_FCN_MAX (5 << 12)
+# define R300_COMB_FCN_RSUB_CLAMP (6 << 12)
+# define R300_COMB_FCN_RSUB_NOCLAMP (7 << 12)
+# define R300_BLEND_GL_ZERO (32)
+# define R300_BLEND_GL_ONE (33)
+# define R300_BLEND_GL_SRC_COLOR (34)
+# define R300_BLEND_GL_ONE_MINUS_SRC_COLOR (35)
+# define R300_BLEND_GL_DST_COLOR (36)
+# define R300_BLEND_GL_ONE_MINUS_DST_COLOR (37)
+# define R300_BLEND_GL_SRC_ALPHA (38)
+# define R300_BLEND_GL_ONE_MINUS_SRC_ALPHA (39)
+# define R300_BLEND_GL_DST_ALPHA (40)
+# define R300_BLEND_GL_ONE_MINUS_DST_ALPHA (41)
+# define R300_BLEND_GL_SRC_ALPHA_SATURATE (42)
+# define R300_BLEND_GL_CONST_COLOR (43)
+# define R300_BLEND_GL_ONE_MINUS_CONST_COLOR (44)
+# define R300_BLEND_GL_CONST_ALPHA (45)
+# define R300_BLEND_GL_ONE_MINUS_CONST_ALPHA (46)
+# define R300_BLEND_MASK (63)
+# define R300_SRC_BLEND_SHIFT (16)
+# define R300_DST_BLEND_SHIFT (24)
+#define R300_RB3D_BLEND_COLOR 0x4E10
#define R300_RB3D_COLORMASK 0x4E0C
# define R300_COLORMASK0_B (1<<0)
# define R300_COLORMASK0_G (1<<1)
@@ -1185,15 +1290,19 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_COLORMASK0_A (1<<3)
/* gap */
+
#define R300_RB3D_COLOROFFSET0 0x4E28
# define R300_COLOROFFSET_MASK 0xFFFFFFF0 /* GUESS */
#define R300_RB3D_COLOROFFSET1 0x4E2C /* GUESS */
#define R300_RB3D_COLOROFFSET2 0x4E30 /* GUESS */
#define R300_RB3D_COLOROFFSET3 0x4E34 /* GUESS */
+
/* gap */
+
/* Bit 16: Larger tiles
-// Bit 17: 4x2 tiles
-// Bit 18: Extremely weird tile like, but some pixels duplicated? */
+ * Bit 17: 4x2 tiles
+ * Bit 18: Extremely weird tile like, but some pixels duplicated?
+ */
#define R300_RB3D_COLORPITCH0 0x4E38
# define R300_COLORPITCH_MASK 0x00001FF8 /* GUESS */
# define R300_COLOR_TILE_ENABLE (1 << 16) /* GUESS */
@@ -1208,18 +1317,22 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_RB3D_COLORPITCH3 0x4E44 /* GUESS */
/* gap */
+
/* Guess by Vladimir.
-// Set to 0A before 3D operations, set to 02 afterwards. */
+ * Set to 0A before 3D operations, set to 02 afterwards.
+ */
#define R300_RB3D_DSTCACHE_CTLSTAT 0x4E4C
# define R300_RB3D_DSTCACHE_02 0x00000002
# define R300_RB3D_DSTCACHE_0A 0x0000000A
/* gap */
-/* There seems to be no "write only" setting, so use Z-test = ALWAYS for this. */
-/* Bit (1<<8) is the "test" bit. so plain write is 6 - vd */
+/* There seems to be no "write only" setting, so use Z-test = ALWAYS
+ * for this.
+ * Bit (1<<8) is the "test" bit. so plain write is 6 - vd
+ */
#define R300_RB3D_ZSTENCIL_CNTL_0 0x4F00
-# define R300_RB3D_Z_DISABLED_1 0x00000010 /* GUESS */
-# define R300_RB3D_Z_DISABLED_2 0x00000014 /* GUESS */
+# define R300_RB3D_Z_DISABLED_1 0x00000010
+# define R300_RB3D_Z_DISABLED_2 0x00000014
# define R300_RB3D_Z_TEST 0x00000012
# define R300_RB3D_Z_TEST_AND_WRITE 0x00000016
# define R300_RB3D_Z_WRITE_ONLY 0x00000006
@@ -1230,7 +1343,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_RB3D_STENCIL_ENABLE 0x00000001
#define R300_RB3D_ZSTENCIL_CNTL_1 0x4F04
- /* functions */
+ /* functions */
# define R300_ZS_NEVER 0
# define R300_ZS_LESS 1
# define R300_ZS_LEQUAL 2
@@ -1240,7 +1353,7 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_ZS_NOTEQUAL 6
# define R300_ZS_ALWAYS 7
# define R300_ZS_MASK 7
- /* operations */
+ /* operations */
# define R300_ZS_KEEP 0
# define R300_ZS_ZERO 1
# define R300_ZS_REPLACE 2
@@ -1249,9 +1362,8 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_ZS_INVERT 5
# define R300_ZS_INCR_WRAP 6
# define R300_ZS_DECR_WRAP 7
-
- /* front and back refer to operations done for front
- and back faces, i.e. separate stencil function support */
+ /* front and back refer to operations done for front
+ and back faces, i.e. separate stencil function support */
# define R300_RB3D_ZS1_DEPTH_FUNC_SHIFT 0
# define R300_RB3D_ZS1_FRONT_FUNC_SHIFT 3
# define R300_RB3D_ZS1_FRONT_FAIL_OP_SHIFT 6
@@ -1262,8 +1374,6 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_RB3D_ZS1_BACK_ZPASS_OP_SHIFT 21
# define R300_RB3D_ZS1_BACK_ZFAIL_OP_SHIFT 24
-
-
#define R300_RB3D_ZSTENCIL_CNTL_2 0x4F08
# define R300_RB3D_ZS2_STENCIL_REF_SHIFT 0
# define R300_RB3D_ZS2_STENCIL_MASK 0xFF
@@ -1275,8 +1385,15 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_RB3D_ZSTENCIL_FORMAT 0x4F10
# define R300_DEPTH_FORMAT_16BIT_INT_Z (0 << 0)
# define R300_DEPTH_FORMAT_24BIT_INT_Z (2 << 0)
+ /* 16 bit format or some aditional bit ? */
+# define R300_DEPTH_FORMAT_UNK32 (32 << 0)
+
+#define R300_RB3D_EARLY_Z 0x4F14
+# define R300_EARLY_Z_DISABLE (0 << 0)
+# define R300_EARLY_Z_ENABLE (1 << 0)
/* gap */
+
#define R300_RB3D_DEPTHOFFSET 0x4F20
#define R300_RB3D_DEPTHPITCH 0x4F24
# define R300_DEPTHPITCH_MASK 0x00001FF8 /* GUESS */
@@ -1286,34 +1403,40 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_DEPTH_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */
# define R300_DEPTH_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */
-/* BEGIN: Vertex program instruction set
-// Every instruction is four dwords long:
-// DWORD 0: output and opcode
-// DWORD 1: first argument
-// DWORD 2: second argument
-// DWORD 3: third argument
-//
-// Notes:
-// - ABS r, a is implemented as MAX r, a, -a
-// - MOV is implemented as ADD to zero
-// - XPD is implemented as MUL + MAD
-// - FLR is implemented as FRC + ADD
-// - apparently, fglrx tries to schedule instructions so that there is at least
-// one instruction between the write to a temporary and the first read
-// from said temporary; however, violations of this scheduling are allowed
-// - register indices seem to be unrelated with OpenGL aliasing to conventional state
-// - only one attribute and one parameter can be loaded at a time; however, the
-// same attribute/parameter can be used for more than one argument
-// - the second software argument for POW is the third hardware argument (no idea why)
-// - MAD with only temporaries as input seems to use VPI_OUT_SELECT_MAD_2
-//
-// There is some magic surrounding LIT:
-// The single argument is replicated across all three inputs, but swizzled:
-// First argument: xyzy
-// Second argument: xyzx
-// Third argument: xyzw
-// Whenever the result is used later in the fragment program, fglrx forces x and w
-// to be 1.0 in the input selection; I don't know whether this is strictly necessary */
+/* BEGIN: Vertex program instruction set */
+
+/* Every instruction is four dwords long:
+ * DWORD 0: output and opcode
+ * DWORD 1: first argument
+ * DWORD 2: second argument
+ * DWORD 3: third argument
+ *
+ * Notes:
+ * - ABS r, a is implemented as MAX r, a, -a
+ * - MOV is implemented as ADD to zero
+ * - XPD is implemented as MUL + MAD
+ * - FLR is implemented as FRC + ADD
+ * - apparently, fglrx tries to schedule instructions so that there is at
+ * least one instruction between the write to a temporary and the first
+ * read from said temporary; however, violations of this scheduling are
+ * allowed
+ * - register indices seem to be unrelated with OpenGL aliasing to
+ * conventional state
+ * - only one attribute and one parameter can be loaded at a time; however,
+ * the same attribute/parameter can be used for more than one argument
+ * - the second software argument for POW is the third hardware argument
+ * (no idea why)
+ * - MAD with only temporaries as input seems to use VPI_OUT_SELECT_MAD_2
+ *
+ * There is some magic surrounding LIT:
+ * The single argument is replicated across all three inputs, but swizzled:
+ * First argument: xyzy
+ * Second argument: xyzx
+ * Third argument: xyzw
+ * Whenever the result is used later in the fragment program, fglrx forces
+ * x and w to be 1.0 in the input selection; I don't know whether this is
+ * strictly necessary
+ */
#define R300_VPI_OUT_OP_DOT (1 << 0)
#define R300_VPI_OUT_OP_MUL (2 << 0)
#define R300_VPI_OUT_OP_ADD (3 << 0)
@@ -1324,26 +1447,33 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_VPI_OUT_OP_MIN (8 << 0)
#define R300_VPI_OUT_OP_SGE (9 << 0)
#define R300_VPI_OUT_OP_SLT (10 << 0)
-#define R300_VPI_OUT_OP_UNK12 (12 << 0) /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, vector(scalar, vector) */
+ /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, vector(scalar, vector) */
+#define R300_VPI_OUT_OP_UNK12 (12 << 0)
+#define R300_VPI_OUT_OP_ARL (13 << 0)
#define R300_VPI_OUT_OP_EXP (65 << 0)
#define R300_VPI_OUT_OP_LOG (66 << 0)
-#define R300_VPI_OUT_OP_UNK67 (67 << 0) /* Used in fog computations, scalar(scalar) */
+ /* Used in fog computations, scalar(scalar) */
+#define R300_VPI_OUT_OP_UNK67 (67 << 0)
#define R300_VPI_OUT_OP_LIT (68 << 0)
#define R300_VPI_OUT_OP_POW (69 << 0)
#define R300_VPI_OUT_OP_RCP (70 << 0)
#define R300_VPI_OUT_OP_RSQ (72 << 0)
-#define R300_VPI_OUT_OP_UNK73 (73 << 0) /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, scalar(scalar) */
+ /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, scalar(scalar) */
+#define R300_VPI_OUT_OP_UNK73 (73 << 0)
#define R300_VPI_OUT_OP_EX2 (75 << 0)
#define R300_VPI_OUT_OP_LG2 (76 << 0)
#define R300_VPI_OUT_OP_MAD_2 (128 << 0)
-#define R300_VPI_OUT_OP_UNK129 (129 << 0) /* all temps, vector(scalar, vector, vector) */
+ /* all temps, vector(scalar, vector, vector) */
+#define R300_VPI_OUT_OP_UNK129 (129 << 0)
#define R300_VPI_OUT_REG_CLASS_TEMPORARY (0 << 8)
+#define R300_VPI_OUT_REG_CLASS_ADDR (1 << 8)
#define R300_VPI_OUT_REG_CLASS_RESULT (2 << 8)
#define R300_VPI_OUT_REG_CLASS_MASK (31 << 8)
#define R300_VPI_OUT_REG_INDEX_SHIFT 13
-#define R300_VPI_OUT_REG_INDEX_MASK (31 << 13) /* GUESS based on fglrx native limits */
+ /* GUESS based on fglrx native limits */
+#define R300_VPI_OUT_REG_INDEX_MASK (31 << 13)
#define R300_VPI_OUT_WRITE_X (1 << 20)
#define R300_VPI_OUT_WRITE_Y (1 << 21)
@@ -1354,14 +1484,16 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_VPI_IN_REG_CLASS_ATTRIBUTE (1 << 0)
#define R300_VPI_IN_REG_CLASS_PARAMETER (2 << 0)
#define R300_VPI_IN_REG_CLASS_NONE (9 << 0)
-#define R300_VPI_IN_REG_CLASS_MASK (31 << 0) /* GUESS */
+#define R300_VPI_IN_REG_CLASS_MASK (31 << 0)
#define R300_VPI_IN_REG_INDEX_SHIFT 5
-#define R300_VPI_IN_REG_INDEX_MASK (255 << 5) /* GUESS based on fglrx native limits */
+ /* GUESS based on fglrx native limits */
+#define R300_VPI_IN_REG_INDEX_MASK (255 << 5)
/* The R300 can select components from the input register arbitrarily.
-// Use the following constants, shifted by the component shift you
-// want to select */
+ * Use the following constants, shifted by the component shift you
+ * want to select
+ */
#define R300_VPI_IN_SELECT_X 0
#define R300_VPI_IN_SELECT_Y 1
#define R300_VPI_IN_SELECT_Z 2
@@ -1379,11 +1511,11 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_VPI_IN_NEG_Y (1 << 26)
#define R300_VPI_IN_NEG_Z (1 << 27)
#define R300_VPI_IN_NEG_W (1 << 28)
-/* END */
+/* END: Vertex program instruction set */
-//BEGIN: Packet 3 commands
+/* BEGIN: Packet 3 commands */
-// A primitive emission dword.
+/* A primitive emission dword. */
#define R300_PRIM_TYPE_NONE (0 << 0)
#define R300_PRIM_TYPE_POINT (1 << 0)
#define R300_PRIM_TYPE_LINE (2 << 0)
@@ -1395,7 +1527,8 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_PRIM_TYPE_RECT_LIST (8 << 0)
#define R300_PRIM_TYPE_3VRT_POINT_LIST (9 << 0)
#define R300_PRIM_TYPE_3VRT_LINE_LIST (10 << 0)
-#define R300_PRIM_TYPE_POINT_SPRITES (11 << 0) // GUESS (based on r200)
+ /* GUESS (based on r200) */
+#define R300_PRIM_TYPE_POINT_SPRITES (11 << 0)
#define R300_PRIM_TYPE_LINE_LOOP (12 << 0)
#define R300_PRIM_TYPE_QUADS (13 << 0)
#define R300_PRIM_TYPE_QUAD_STRIP (14 << 0)
@@ -1405,29 +1538,32 @@ I am fairly certain that they are correct unless stated otherwise in comments.
#define R300_PRIM_WALK_LIST (2 << 4)
#define R300_PRIM_WALK_RING (3 << 4)
#define R300_PRIM_WALK_MASK (3 << 4)
-#define R300_PRIM_COLOR_ORDER_BGRA (0 << 6) // GUESS (based on r200)
-#define R300_PRIM_COLOR_ORDER_RGBA (1 << 6) // GUESS
+ /* GUESS (based on r200) */
+#define R300_PRIM_COLOR_ORDER_BGRA (0 << 6)
+#define R300_PRIM_COLOR_ORDER_RGBA (1 << 6)
#define R300_PRIM_NUM_VERTICES_SHIFT 16
-// Draw a primitive from vertex data in arrays loaded via 3D_LOAD_VBPNTR.
-// Two parameter dwords:
-// 0. The first parameter appears to be always 0
-// 1. The second parameter is a standard primitive emission dword.
+/* Draw a primitive from vertex data in arrays loaded via 3D_LOAD_VBPNTR.
+ * Two parameter dwords:
+ * 0. The first parameter appears to be always 0
+ * 1. The second parameter is a standard primitive emission dword.
+ */
#define R300_PACKET3_3D_DRAW_VBUF 0x00002800
-// Specify the full set of vertex arrays as (address, stride).
-// The first parameter is the number of vertex arrays specified.
-// The rest of the command is a variable length list of blocks, where
-// each block is three dwords long and specifies two arrays.
-// The first dword of a block is split into two words, the lower significant
-// word refers to the first array, the more significant word to the second
-// array in the block.
-// The low byte of each word contains the size of an array entry in dwords,
-// the high byte contains the stride of the array.
-// The second dword of a block contains the pointer to the first array,
-// the third dword of a block contains the pointer to the second array.
-// Note that if the total number of arrays is odd, the third dword of
-// the last block is omitted.
+/* Specify the full set of vertex arrays as (address, stride).
+ * The first parameter is the number of vertex arrays specified.
+ * The rest of the command is a variable length list of blocks, where
+ * each block is three dwords long and specifies two arrays.
+ * The first dword of a block is split into two words, the lower significant
+ * word refers to the first array, the more significant word to the second
+ * array in the block.
+ * The low byte of each word contains the size of an array entry in dwords,
+ * the high byte contains the stride of the array.
+ * The second dword of a block contains the pointer to the first array,
+ * the third dword of a block contains the pointer to the second array.
+ * Note that if the total number of arrays is odd, the third dword of
+ * the last block is omitted.
+ */
#define R300_PACKET3_3D_LOAD_VBPNTR 0x00002F00
#define R300_PACKET3_INDX_BUFFER 0x00003300
@@ -1436,6 +1572,23 @@ I am fairly certain that they are correct unless stated otherwise in comments.
# define R300_EB_UNK2 0x0810
#define R300_PACKET3_3D_DRAW_INDX_2 0x00003600
-//END
+/* END: Packet 3 commands */
+
+
+/* Color formats for 2d packets
+ */
+#define R300_CP_COLOR_FORMAT_CI8 2
+#define R300_CP_COLOR_FORMAT_ARGB1555 3
+#define R300_CP_COLOR_FORMAT_RGB565 4
+#define R300_CP_COLOR_FORMAT_ARGB8888 6
+#define R300_CP_COLOR_FORMAT_RGB332 7
+#define R300_CP_COLOR_FORMAT_RGB8 9
+#define R300_CP_COLOR_FORMAT_ARGB4444 15
+
+/*
+ * CP type-3 packets
+ */
+#define R300_CP_CMD_BITBLT_MULTI 0xC0009B00
+
#endif /* _R300_REG_H */